Angle Grinder dust Collection Attachment, Cutting dust Shroud 4 inch to 5 inch AD-1803125

OK , I like this tool. I often have to cut old 5/8" thick stucco over lath and wire mesh inside houses.This tool is not perfect however it makes the job just a miserable moderately dusty project. I like the adjustable depth of cut since I often make a first cut about 1/4" deepI made slight modifications to the tool1) the mounting clamp diameter was not big enough. I replaced of the clamp screws with a longer 8-32 screw.2) after mounting the diamond wheel I taped over the wrench access hole in the side of the grinder to improve the vacuum.I have as shopvac directly connected to the tool, if I can find an old vacuum cleaner hose I'm going to make that connection permanent.I have noticed that I get better dust pickup when I am pushing the grinder forward than when I am pulling it back. I can see why , it's an airflow thing.One other suggestion , always blow out your grinder to remove dust after using with this appliance. Stucco, drywall and cement dust is very abrasive ,gets in everywhere and kills good tools

I had high hopes but it didn't fit my Erbauer ERB386GRD. Well, it did, but not well enough to feel safe in going outside and using it. It's a good concept and seems well made but as others have said, there are too many eccentricities to be fully practical/functional.1) The mix of collar sizes are good, but when the metal collar is tightened up around them, they can still shift.2) The metal tightening collar on my example wasn't welded at 90º to the plate, meaning it reduced the blade clearance because the blade wasn't parallel to the shroud.3) The use of bolts with thumb turns is nice until you realise it reduces the clearance to the grinder body, also limiting the mounting positions possible.4) There seemed to be only one way to get it to 'fit' my grinder and that was at 90º, with one thumb turn bolt removed, and the blade about 3mm away from the inside of the shroud.5) The metal flange pad sits on top of the one already provided with your grinder. That moves the blade away from the plastic shroud but gives less room to tighten the flange up when the blade goes on. The included spanner had pins slightly wider than the Erbauer flange, making it harder to tighten.I've returned it because it didn't feel safe or secure enough to use. That's not to say it won't fit your angle grinder if it's the same make/model someone else has had success with.

It works. A bit of a field to set up but it makes the job clean and accurate and fast when cutting masonary to depth for a pipe chase and when chasing out old pointing for replacement. It is plastic so DIY not pro if you need thatbuy a metal one at £100.

This was worth the money. It has saved me and the room being covered in dust. Had to chase out several walls ready for the electrics so this was life saver. When you first use the grinder there is a little dust that flies out but when it’s flush against the wall and the Hoover is attached and on it holds the dust in. The hoover adapter could be better as this kept sliding off at times but you could attached a tie clip to hold it in place. Definitely so pleased I found this item. Such a good idea

Not great fit to Bosch hand held grinder and limited use as let's too much dust out

The media could not be loaded. Can’t fault it works very well attached to my dust extractor, no dust

The media could not be loaded. Great bit of kit for that price, around 70sqm of pointing run through with it and works really well. Easy to install, Henry hoover attached, thumbs up!

Having purchased this for a small home project (cutting down a small section of wall) I can say this item is just a pure waste of time.1) it took over 30 minutes just to fit it and even this fitting wasn't great (felt very flimsy)2) dust just poor's out the bottom and doesn't get sucked up - I had better success with just holding the hoover next to be cutting !3) you have to move the cover each time if you want a tight cut (against a wall)item got used for less that 5 minutes before it was back in the box !Item is not fit for purposeAVOID AT ALL COSTS