5.8G Transmitter 200mW with Caddx Turbo Micro F2 CMOS 2.1mm 1200TVL FPV Camera - MULTI-C

الوصف

Main FeaturesAdjustable 4 modes:25mW/100mW/200mW/OFF Betaflight/Cleanflight OSD configuring parameterSupport SBUS configuring parameterClean powerup and channel switching without interference to othersMiniature and light weight designSpecificationsModel: EWRF e7087UFrequency: 5.8G 48CHTransmitting Power:25mW/100mW/200mW/OFF(Pitmode)Power supply:DC7-24VSupply current:110mA(25mW)/160mA(100mW)/210mA(200mW)Weight:2.9gSize:Design for RunCam User Guide1.LED indicationThe red LED indicates the state of working mode or the item when setting the VTX(flashing 1 time means selecting the channels, flashing 2 times means selecting the bands, flashing 3 times means selecting the power levels).The blue LED indicates the state of Pitmode or the value of item when setting the VTX(e.g. when selecting the channels, 3 times of flashing means channel 3. When selecting the bands,3 times of flashing means band C.As for the item of power levels,3 times of flashing means at the power level of 200mW)2.Working mode indicationAfter powering up, the red & blue LEDs will signal the following three items of VTX in turn: channel, band and power level(the flashing times of the red and blue LEDs indicate the item and the value respectively). After that, the LEDs indicate the working modes.Normal: The red & blue LED are on. Pitmode:The red LED is on and blue LED is off. 3.SettingPress and hold the button until the red LED flash 1 time which means the item of channel selecting, then press the button can select the channels(blue LED flashing times corresponds to the channel 1-8). Press and hold the button again,the red LED will flash 2 times which means the item of band selecting, then press the button can select the band(blue LED flashing times corresponds to the band A-F).Press and hold the button again,the red LED will flash 3 times which means the item of power level selecting, then press the button can select the power(blue LED flashing times corresponds to the power level).Finally, press and hold the button, save and exit the setting of VTX(This step is essential for setting).Press the button twice will toggle the ON/OFF of Pitmode.4. SBUS settingConnected to the 6th channel of the receiver ,turn back and forth the switch can change channels. The operation similar to key trigger mode.5.OSD settingFor Betaflight/Cleanflight OSD setting of channel,band,power and Pitmode,please referring to 'Betaflight OSD setting of EWRF Transmitter'for details. Note:1.Make sure that there is enough space for airflow when installing the module on the drone in case the overheating protection starts to reduce the power even to shut down at the worst.2. Please install the antenna before powering up for a longer use life. SpecificationGeneral Information Type: Antenna,Transmitter and receiver Compatible with: Vehicles & Remote Control Toys Feature: New 5.8G 48CH FPV Transmitter 25/100/200mW Support smartaudio DC 7-24V with Caddx Turbo Micro F2 CMOS 2.1mm 1200TVL FPV camera Single Size: 1.9*1.9*0.35 cm Single Weight: 2.9g Dimension and Weight Product weight: 0.0029 kg Package weight: 0.0300 kg Product size (L x W x H): 1.90 x 1.90 x 0.35 cm / 0.75 x 0.75 x 0.14 inches Package size (L x W x H): 13.00 x 10.00 x 5.00 cm / 5.12 x 3.94 x 1.97 inches Package Contents Package Contents: 1x EWRF-e7087U Transmitter, 1 x Caddx Turbo Micro F2 FPV Camera F2, Camera Accessories: 1 x Aluminum bracket,1 x FPV silicone cable (4-pin port one side, 3-pin port the other side) , 1 x Internal hexa