KRYDEX IPSC USPSA IDPA Competition Shooting Multi-Angle Adjustment Speed Shooter's Pistol Magazine Pouch Mag Holster Holder

Great fit for different mags and pretty good quality for the money

I have purchased six total mag holders. I have a Wolf Tactical belt with quick release buckle. I used these mag holders right out of the box with NO adjustments. I slide them on my belt at each competition along with my holster and have had zero issues. I can move them between my belt loops on my pants and they also adjust/tilt and hold mags with no issues. I have not had a mag pop out or fall out like some reviews. I highly recommend these mag holders. I used them for double stack 9mm. I would challenge any of you poor reviewers to a shooting competition and guarantee I will beat you!

Range accessories get expensive fast. I bought these for my range bag that I leave in my truck for quick after work practices. I do not like leaving my more expensive belts and gear like my KYWI’s vulnerable in my truck all day unattended. Very sturdy, your belt slides right through and fits my 1.5” blue alpha gear belt perfectly, and the adjustable retention nut works as intended. They have a good size gap from the belt which makes for a very easy draw. I also enjoy how the side is open allowing me to index the magazine very easy when drawing. So far so good, have taken them out 10 times or so. For the money I don’t think you can go wrong with these.

I ordered one of these to pouches to test it out. Loved it so much I ordered 4 more. These pouches are identical to the Black Scorpion pouches. Exactly the same. The only difference is the Black Scorpion emblem. They are fully adjustable. They have a swivel tension mount so you can rotate them and cant them towards or away from your body. You can also raise or lower them on the belt mount. The only negative I have is that it takes a bit to get them mounted on the belt so they don't lend well to a rig where you're swapping or moving the pouches often. Other than that, they are a great value. One recommendation is to use Loctite on the threads once you get them to where you want so they don't loosen and move Mainly the main screw that holds the swivel mount.

The best bang for your buck, however, it's a real pain to attach to your belt. You've got the four tiny hex bolts that are somewhat blocked by the belt attachment - really frustrating to turn a standard allen key. And the bolts are super easy to lose if you're not careful - pro tip, use tape on the back side of the bolts to hold them in place while you're tightening them onto your belt. Retention is below average, I'm using Walther PDP double stack 9mm magazines, and I can't seem to torque down the retention bolt far enough to get a snug fit. The ability to set infinite angles of cant positions are outstanding though and easy to adjust. Overall, worth the price. I wouldn't trust my life to them or use them for any important USPSA matches, but perfect for a new shooter or weekend run and gunner.

Great alternative to the big name brands out there at a fraction of the price. Looks great and fits well on my competition belt. Excited to use it.

I'm running a G21 45acp magazine in these, they hold somewhat okay. The insert that is interchangeable to adjust for different magazines falls out easily. The small nuts don't lock on the back of the holder and fall out too easily. They don't offer any extra nuts in the package or any extra magazine inserts, so if you lose one, your out of luck. I've used these in two training sessions and in not sure that I keep using them going forward. Id suggest looking at another system, this one isn't user friendly enough.

I use these for USPSA , SCSA , PCSL and all hit factor matches. No problems as of yet. Had them for 9 months. Easy to use , adjust and install. Will upgrade later as I improve but these are excellent for all levels of shooters. I did personalize them with some custom paint and decals

These work awesome. I’m no competition shooter but I’ve ran my mags through them a ton and they have held up perfectly. They showed up exactly as they were advertised. Fast shipping as well!

They work well with Glock mags

These mag holders are affordable knock-offs of high end, competition-oriented holders which can cost 3x+ more per unit. If you are patient and handy with small tools, they can provide a low cost entry into competitive practical shooting sports. They are highly adjustable to a range of magazines and fit most common belt systems (up to 1 1/2” width). Made of plastic, they will not have the lifespan of high end units made of aluminum etc., but until you get into high frequency, intense practice and competition sessions they do the job. You have to spend time adjusting them to fit your mags, dealing with many tiny nuts and screws as others have mentioned (would be nice if company included some spares as they do tend to go walkabout!). Getting them mounted on your belt is also a bit of a pain; once you get them setup you will want to leave them on. As shown in accompanying pictures, I made a couple of mods which improved holders a bit. As they come, mag retention is by friction alone, which changes with use, temperature, etc. You can tighten the top black knobbed bolt down for secure retention, but then mags may be sticky to pull out. I epoxied 3/4” by 1/8” thick rare earth magnets to the inside center of the outer panel of each holder, so the magnet was centered over the fortuitously positioned hole through the inner panel of each holder (silver disc visible in photo). The resulting clearance is perfect for effective mag retention, without any scraping or interference and allows one to reduce the friction screw pressure, giving a secure but slick action. Note some competitions disallow magnet-only holders; it’s not clear if they would rule this system out, but if that ever was an issue one can quickly undue 2 nuts and remove the outer panels with attached magnets and use friction retention alone. Also as seen in photos, I drilled a tiny pair of holes in lower rear corners of each side of holders, and pushed through a 4-40x1” screw, with a piece of black plastic tubing as a spacer (cut to fit my mag thickness), with a nyloc nut on inner end. This addition made the mag holders much more sturdy and stable. Finally, as others have suggested, once I had all the holders adjusted so mags fit well, and got them mounted on the belt at the correct angles (tilting slightly away from belt, and slightly forward works), I applied blue medium threadlock to every nut and bolt (except top friction knob) and retightened everything carefully. Several friends use these holders as well, without modification, and seem happy. They use the holders with Krydex belts which also seem fine. I had a similar but higher-end Black Scorpion belt, on which these customized holders also work well.

Seems well built. Easy to switch to lefty holds glock and smith&wesson mags supper tight but are easy to pull out and put back so There great for speed loading but these are my first mag holders like this so i have no other brands to compare too. I will repost. If they break

Received this 2 days ago, and they are great. Packaging was great. Only thing that I question is that to adjust the angle and/or tightness of mag holder you need an Allen key which was not included. I didn't take off a star because almost everyone has allen keys. These mag holders are a welcome addition to my range days.