SHDIATOOL5-Piece 4 in. Diamond Jig Saw Blades for Tile Ceramic Brick Marble with T-Shank 46 Grit

the blades are to thick, they will not work on a table saw. I tried on e on a jig saw and it bent.

These might work for you depending on your plans. I was trying to cut a hole in an old sea shell marble vanity top for a drop in sink.These broke too easily. I was on my third one before making a foot’s length of cutting. By then, I realized the bowl of the sink was too thick for my job to be realistic.These will cut marble and could work well on thin materials; however, they come in a 3-pack for a reason. I would plan to stock up and plan for some slow, messy jig saw work in the future.

I bought a five-pack expecting to use all of them For a job that involved cutting fiberglass-epoxy tubing. This material is hard on carbide tooling and with 20 feet of cuts I knew diamond was the way to go. These blades are thicker than I’d like but they hold up well and to my surprise I only needed one blade to finish the entire job. My cuts were all straight, but I noticed there was enough grit on the sides of the blade to accommodate curves.

Not that good... waste of cash!

I could not tell how well they cut because they broke so quickly. Probably fine for very slow, straight cuts, but any torque sideways snaps them off immediately.

Needed to cut a heavy roof tile. Ordered these blades and they arrived the next day. The blades cut the tile very easily. The cutting was done in 5 minutes and the tile was back on the roof that day.

I've ordered alot of diamond products from this store. Everyone being awesome. Until these saw blades. The shank was too wide ti fit my makita jigsaw so I had to sand the sides down bit. Then the tile I strictly bought these for broke the tile and almost took off diamond coating.

Great 👍

Utilizzato per tagliare materiale sicuramente meno duro e impegnativo rispetto alle piastrelle per cui queste lame sono progettate (lastra in fibra di carbonio, da 4 mm).Il prodotto ha effettuato il taglio come richiesto, e il materiale tagliente sembra aver lavorato bene, rimanendo adeso al metallo di base.Al secondo taglio, la lama si è spezzata di netto poco sotto l'attacco, dimostrando la scarsissima qualità del metallo di cui è costituita (e rendendo oltretutto difficile il recupero della testa della lama incastrata nella sede dell'utensile).Pessima cinesata, ma dal costo non così contenuto (15 € 3 lame); rispetto ai problemi verificati da altri utenti, che sembravano potersi risolvere semplicemente raffreddando durante il taglio, la bassissima vita della lama fa pensare che esistano sicuramente migliori soluzioni da produttori più seri e che effettuano qualche genere di controllo qualità.Deluso dal prodotto, spedizione di Amazon eccellente come sempre.

Die Lieferung war zügig und gut verpackt.Ich verwendete sie Sägeblätter um einer Fensterbank in der Tiefe zu kürzen, sprich an der langen Seite einen Streifen abschneiden.Es klappte besser als gedacht. Die Pendelung der Säge stand auf 1 (von 3 Stufen) und langsam ging es durch das Material. Für 2,5 m brauchte ich 2 Sägeblätter, weil eines wegknickte.

Artikel ist mit 4" ausgewiesen, d.h. die Gesamtlänge sind 4" = 100 mm. Ich hatte angenommen das die Sägefläche (Widia oder Diamant beschichtete Sägefläche 100 mm ist) Artikel ist unzureichend beschrieben.Ich will Rückgabe erwirken, da Ware für meinen Verwendungszweck ungeeignet ist. Die nutzbare Dägefläche ist zu kurz sollte mindestens 100 mm betragen.Habe inzwischen über Baumarkt entsprechenden Artikel gefunden

Quality is okay… but I only received one blade

nach auflöten von Diamanten nicht mehr nachgehärtetbricht nach wenigen bewegungen