B-Tech BT77 Ultragrip Pro Speaker Mount, Set of 2, Side Clamp with Tilt and Swivel, Black

I have M-Audio DSM speakers as I grabbed a pair on closeout before M-Audio stopped making them. Well, I didn't want them on my computer table as they are HUGE so I looked for the best alternative. The problem with most solution sis that they don't GRIP the speaker and I didn't want to have to worry about the speakers falling over. You see the, M-AUDIO, and I'm sure countless other speakers have rounded edges and are quite wide. The Recelco mount seemingly specked out fine but I was still in the "believe it when I see it" camp. These come with nice instructions but here are some tips: -Go to your hardware store and buy plastic anchors for these. I couldn't find a stud anywhere close to where I wanted to hang my 30 lb speakers, and the plastic studs do the job - If not using a stud buy longer screws with your plastic anchors - The clamping mechanism is tricky as it's screw based, get it fairly tight and then alternate sides until you can get it as tight as possible. - Home depot sells insulation tape that'll work instead of the stuff that comes on these to grip the speaker After installing using the above parameters this easily has held my large rounded corner speakers for over six months. I love that you can slightly angle the speakers down at yourself if you put them above ear level. These look nice with cover on them and are more than sturdy. Even without the changes I made above for most normal speakers these will work, but if you have larger weird speakers like I do take the extra moment and make the changes I did! You don't want to worry about your expensive speakers falling! Great product. BTW, I went to Tiger Direct, Best Buy and Target and couldn't find anything this good, so save yourself the time!

Installation was fairly straight forward. They include bolts and anchors for concrete but not for drywall. One one side it did not align with a stud so I had to buy some drywall achors. The only minus is though its a wall mount there is no place for cable management, so I had to mount it next to the hole where the cable comes out from my wall.

Purchased the Rocelco B-Tech Ultragrip Pro Loudspeaker Wall Mount Brackets for my NHT 1.5 bookshelf speakers. Due to the configuration of our living room and how the furniture is arranged, there was simply no room for small speaker stands and I didn't want them on the floor getting kicked around. My NHTs are 16.5"H X 25"D X 7" wide and weigh 16 lbs each. These are ultra high quality wall mounts, very heavy duty and I have no doubts they will support my speakers more than adequately. FYI, I did end up customizing my brackets somewhat with good results. Once I had my speakers mounted, I noticed they were several inches away from the wall. The mounts are obviously made for a wide range of speaker sizes and would hold much larger speakers than I have. I was able to cut a couple of inches off the bracket support post so that the distance between the wall and the back of the speakers is now only about an inch or so. It also meant I had to drill a couple of new holes in each bracket, but for my speakers, the weight is now more centered on the mounting bracket as well. My wife wasn't wild about the idea of mounting speakers on the wall, but we really didn't have any good options and these brackets look very professional. I highly recommend them if you just don't have space otherwise for medium size loudspeakers.

I picked up a pair of BIC America DV62si's ( BIC America DV62si Bookshelf Speakers (Pair, Black) , also a 5-star review if you are looking for some great-sounding speakers) that came in without the ability to mount to a wall and, at about 20 pounds each, were too heavy to use with my existing wall-mounts. So I did some research and ended up choosing these from everything else. Here are the four things that sold me the most: 1) It could hold 55 pounds, which means holding on to 20 pounds wouldn't be an issue, even with vibration. I read other reviews and I saw some that should hold 20 or more pounds but the reviews stated that it would fail with speakers that shouldn't have had problems. 2) This already had 15 5-star reviews, all saying that they worked flawlessly. How could I refute that? After reading other products with bad reviews, this one really stood out. 3) This grabs the speakers from the bottom instead of needing to drill them into the speaker itself, thus relying on the speaker itself to support the weight. I'm no speaker expert, but when everything else (that seemed to fail quite often) held onto it from the back of the speaker I got really concerned. Because if the speaker box vibrates off the wall mount I think you'd have the replace the entire speaker. 4) These looked pretty amazing! I really liked the clean look and this appealed to me. There was one thing that made me hesitate, and that is the price. You can find things that should hold heavy speakers for about half this price, but in the end I wanted to purchase something that I knew would work and I decided to go with this. Setup is real easy and took about half an hour to put both of my speakers up. I would have been faster but I had to almost turn into a contortionist to get one of my speakers up because of the furniture located under it. So if you have a clean shot at the wall, you should be able to throw both up in about twenty to twenty-five minutes. And it looks GREAT!! Every Tuesday night I host a movie night with the neighbors. None have visited without commenting on how it looks. I'll upload some pictures. I've had them up for about two weeks and have subjected those speakers to as much punishment as possible and they have worked flawlessly. I could not have been happier with how these have turned out!!

These are most definitely heavy duty work fabulous, would highly recommend.

J'ai cherché partout des supports muraux pour mes enceintes triangle Cométe EX (qui font déja leur poids!), aucun produit ne correspondait à ce que je voulais. Je suis tombé par hasard sur ceux ci, et je dois avouer que j'étais septique quant à la qualité au vue du prix, et bien non, au contraire, ces supports sont tout simplement excellents ! Ils inspirent confiance (et il vaut mieux vu le prix des enceintes!), pour un montage sur du ba13 attention, utiliser des chevilles molly, et si comme moi vos enceintes sont assez lourdes, renforcer le placo si possible pour éviter les mauvaises surprises! Concernant le systéme de fixation de l'enceinte, c'est très simple, l'enceinte est serrée sur les cotés (en contact avec un caoutchouc anti-dérapant)dans mon cas j'ai vissé l'arrière des hp pour assurer le montage et ainsi éviter un glissement car je les ai réglé vers l'avant. La seule amélioration que je pourrais formuler serait d'avoir un passage du cable (mais c'est vraiment un détail), j'ai percé la plaque en plastique et le tour est joué, installation digne d'un pro!! Bref si comme moi vous recherchez un support sécurisant, design, réglable dans les deux sens et adapté à quasi toutes les enceintes bibliothèque, n'hésitez pas une seconde, ce produit est le seul existant de ce type et à un prix imbattable ! Merci Amazon, délai, emballage etc au top!

I supporti sono belli esteticamente e si adattano ad ogni ambiente. Robusti e facili da montare e hanno un bel range di larghezza e regolazione in orizzontale che in verticale. Forniti di tutto il necessario per l'installazione (tasselli, gommini antiscivolo). Per un upgrade definitivo consiglio di mettere una goccia di silicone o colla a caldo per fissare la copertura di plastica sulla staffa perché ad alto volume iniziano a vibrare un po.

This is very well made. It was intuitive and easy to assemble and mount. The fact that the skeleton of this is made of wrought iron gave me confidence that this would last long and hold up my Klipsch speakers easily and for long. Highly recommend

La instalación fue bastante sencilla, los utilicé para un par de Yamahas Hs7 y no tienen ningún problema en tolerar el peso. El ajuste es bastante cómodo y no afecta a la construcción del monitor