Trunk Lock Latch for Toyota Camry 2007 2008 2009 2010 2011 Replacement Camry Rear Trunk Lid Release Latch Door Lock Actuator Motor Assembly Replace 64600-06010, 931-860

Works perfect and easy to install. Very happy with this. Longest part was taking off the trunk cover. YouTube video describes the process. Only item not covered is that there is another plastic clip in the rod that attaches to the part. You also slide to the side to remove the rod and reuse both the rod and clip on new part. Hope it lasts another 18 years.

It took me half an hour to do this repair. If you have the correct tools this job goes quickly. While you have the door panel off the door, lubricate the regulator to keep it working well.White lithium grease works well and stays in place between the moving gears.Don't forget to put a few dabs on all the felt guides that hold the glass! It will help the window motor last much longer not having to work so hard.

Works perfectly on my car and will recommend this to other customers

"This part functions just like the original and is significantly more affordable compared to what dealers or other sellers offer. I can't speak to its long-term durability yet, as I've only recently installed it, but so far it works perfectly without any issues. Very satisfied with the purchase at this stage.

I used this to fix the rear latch in my wife’s 2004 Toyota Sequoia.

I'm assuming the reason you're here is because you got yourself an aftermarket security system and it has the ability to open your trunk and you didn't have this ability stock and you want to add it. If that's the case read on, if not, this will still work for you as a replacement and that's all you need to know.I bought this because I had wanted to put a security system in my Toyota that didn't come with one. I had my viper kit installed and after the fact installed this myself as it would've cost way too much for the amount of work it took. However it took me a lot of thinking so I'm going to try to save you the extra heart ache and tell you how to wire this up.It fits right in like it should but when you wire it up it's not going to work right. Aftermarket security systems for accessories like lock, unlock, trunk, etc functions send out or recieve a ground signal. The trunk actuator is going to want to be switched by a +12v signal. I went through all the testing phases to try and figure out why and all I could figure out is that you're going to need a relay to give each component the signal that it needs.I know this sounds complicated but it's actually easier than it sounds. The relay you'll need will have four pins, two to engage the coil and two to create a path to the actuator. I recomend you get the same wire terminal pieces that work with the relay you get from your local autozone.For starters you need to send a CONSTANT +12v DC signal to the coil of the relay. You'll probably have to send one back there, which kinda sucks, but that's not terribly hard either. Go from your fuse box or just patch into you 12v outlet near the center console. Don't worry about your fuses because this actuator doesn't need much power to work anyway. Route the wire along the driverside doorpanel amd through a small whole in the corner of the rear bench seat. Go up through the roof of your trunk and stick the wire inbeetween all the other wires going to the trunk lid.Once you've done that, you'll route the ground from your security system trunk signal to the GROUND of the coil. This will create a path when you engage the trunk button on your remote. Once you've done all this, the rest is easy. You'll short the terminal that you just created with the +12v DC to the contactor. Should take no more than 6 inches of wire. Once this is done, send the remaining contactor to the +12v wire from the wiring harness on your car.NOTE: I never like cutting factory wires as this is permanent so I went to my local Pull-A-Part and got a wiring harness for cheap.I know you wished this would be easier but since I'm assuming you're a lower trim Camry you didn't come with the trunk function from the factory. Once this is done, make sure your connections are tight and you're all set.This is just going to pop the trunk open so if you want it to open most of the way you can YouTube bungie cord trunk opener or something like that. This is a mod that will open your trunk nearly all the way. I've had mine for years and it's worked for me as long as you don't get super cheap bungie cords.

Installed perfectly and operates as a factory part

Part fit perfectly, local parts supplier stated it was a dealer item only. Seller had item delivered in less than 24 hours. Awesome customer service and value