Ring Chime Pro

Bought 3 ring cams for outside the house but front door & back door cams kept losing connection. Our house gets pretty spotty WiFi because we’re lower in elevation from houses above ours. Got this Chime Pro & plugged it in upstairs, easy set up, everything synced in. All cameras work great now. Worth the additional cost after spending almost $600 on cameras.

I got a second Ring camera, but my first one stopped working. I tried a cheap internet extender, but it still wouldn’t connect. The Ring Chime Pro was perfect, it connected with my Ring cameras right away and completely fixed my issue. I also love that there’s a light at the bottom that helps keep the room illuminated, the battery is directly connected to the plug, and the size is perfect. No noticeable lag time at all. Highly recommend if you’re having connection problems!

I first bought a Ring doorbell cam 4 and hard wire installed it. RSSI signal strength was around -65 which was ok but not good. Because RSSI is a negative number, the lower number the better. For example, the best RSSI is -59 to -1. I then bought the Ring Chime Pro and installed it in a wall outlet between the router and the doorbell. The app said, no good, find a different location. I tried three more locations, including a wall outlet inside the house located only about 8 feet from the outside doorbell. Signal strength still not good. Finally, I used an extension cord and located the Ring Chime pro on top of a dresser that is literally one foot from the doorbell, with only the house's outer wall between the doorbell cam and the Ring Chime Pro. At first, still no good! I felt defeated. But wait, there is more! I checked on it a couple of hours later and all of a sudden, the RSSI was great, it was -44. My conclusion is that do not be thrown off by an initial bad reading. Apparently it takes awhile either to establish the good connection and/or the Ring cam device only updates the signal strength report every so often. So now I conclude that it is possible that some of the other locations I tried may also work. To adequately test each location, I believe you need to install it and let it sit there for awhile. In the Ring app, go to the Ring doorbell cam settings, click on "Device Health" to see the current RSSI value, but also scroll down and to see the date and time of the last "Device Health Check." If that time is a couple of hours ago, do something to the doorbell cam to trigger it, like ring the doorbell, and then check device health again. I did this and the RSSI value changed for the better. It has now been over a week, and I am consistently getting an RSSI from the router to the Ring Chime Pro, and from the Ring Chime Pro to the Ring cam, of about RSSI-45, which is great. Other things: As other reviewers have noted, you truly can easily turn off the nightlight, the chime alerts, and even the little blue status light. In other words, you can easily make the Ring Chime Pro a completely dark and silent device whose only purpose is the signal strength boost. This is all I wanted because my doorbell cam is hard wired to my mechanical doorbell chimes and I don't need any part of it except the signal boost. Thus I give five starts to the Ring Chime Pro. I have not yet reviewed the Ring doorbell cam itself, but my comment on that is that if you have a brick house, like mine, and your doorbell is in a corner far away from your router, you will probably need to also pay $49 for the Ring Chime Pro, unless you already have a system of mesh wifi boosters. Also, the Ring Chime Pro is super easy to install. Assuming you have already installed the Ring app on your phone, you just plug the Ring Chime Pro into a wall outlet. Then you do have to wait a few minutes while the app sends a firmware update to the device. After that, the app will start giving you prompts that the location is no good. But if you feel the location is pretty good, I would wait, as described above, and see if the signal strength improves over time.

Works great for signal booster! My RSSI has significantly gone up since I got this little guy therefore my picture clarity as well! I had my WiFi mesh extender as close as possible to the ring doorbell before but i was getting health alerts as it was too close to my router. And even then it was hovering around -65 ish which isn’t great. Problem solved once I plugged in this guy and moved my mesh extender to a better part of the house. RSSI is now in the low -40s. Also kind of enjoy the built in light that notifies you of a doorbell press if you decide to not use any chime sounds. Only reason not five stars is you can’t even see the chime pro in the ring app if you are a shared user, have to be main account holder, but still not the end of the world. Definitely worth it.

The Ring Doorbell Camera comes with a Chime Kit Mini. It's a small device that installs into the existing home chime unit. It provides a simple chime sound when the doorbell button is pressed on the camera unit but this Ring Chime Pro will augment that Chime Kit Mini providing an abundance of additional chime sounds, a night light, and act as a Wi-Fi extension. You select a wall receptacle to plug it into and then add it via the Ring App to your existing Wi-Fi system, that's it. Select your Chime sound, control the night light from the app, and use it to connect devices to your home network. If you own a large home you can install more than one to better hear the door chime in remote parts of your home. It connects via Wi-Fi. It's super simple. I can also attest that Ring has 24/7 SUPERB support if you have any issues or questions. Highly recommended. Cheers!