Front Inner Splash Guards Fender Liners for 2007-2019 Jeep Wrangler JK JKU 4WD Bolt-on Style Aluminum Flare Wheel Well Cover

First off, they could have included a couple self-tappers to complete the install and deleted the mystery round plate that does absolutely nothing(wtf?). It fits pretty well and might require a little bending which is pretty easy to do by hand. I honestly expected to have to grind some edges to avoid rubbing, but didn’t have to. Looks great when installed and fits pretty good. I picked these because they didn’t have a cheesy design which is apparently hard to find on Amazon. Definitely could have used some washer for the tiny bolts. They included so many extra nuts that I used those as “washers” to prevent the bolts from pushing through. You’ll need a few self tappers and some washers to complete install.

I got these because the price point and material finally hit the right spot. The reviews were also really helpful so I knew what to expect. Because the price was low, I also picked up a rivet nut tool at harbor freight for this project and what turned out to be an other $40 of rivet nuts and m-5 screws because my wife wanted black hardware. I am satisfied with the product. But, on my 2008 Jeep Rubicon unlimited the produce is about 1/4 inch too short on the top/front corners. The gap is hardly noticeable, but I know it's there. Also on the drivers side, lower corner the cover seems like it needs another attachment point, but it's too short and there isn't enough metal on the body lip. If tapped the cover rattles on the body/frame, I did not hear it on the road though. I will probably just cut a little extension tab so that I can screw it down.Installation was not "easy." It required a little bit of skill as well as the right type of drill bits for the install. Make sure you have the right sizes and type. The aluminum product is easy to drill, gut the jeep, namely the radiator mount needs something harder than the easy to find "titanium." (I will be looking for a set of cobalt bits for this type of project." A helper would have been nice but I was able to finish the project in about 3 hours. I had to drill some extra holes in different locations due to previous modifications I had made.I will update this for long term after we run some trails too.

The media could not be loaded. I really have mixed feelings on this one. There’s some good features and some things that really need improvement.I’ll start with what I like:1. Aluminum, no worries about weight or rust.2. Non-branded. No gimmicky looking stuff to make it look… well cheap.Now what could use improvement:1. The hardware. If you’re going to keep the bolts that come with it, you need to get yourself some washers, trust me. Read the other reviews. It comes with M5 socket caps with no washers, ideally it should come with M6 button heads.2. The instructions are actually not bad but they don’t mention anything about the mystery disk. Take a look at the video, you’ll understand.3. Fitment, it needs a little persuasion to fit but even so, there’s a gap.4. This one is my biggest gripe. It doesn’t cover the gap between the door and inner body panel allowing dirt and grime to build up and possibly damage the body.

These were pretty easy to install and fit great. They are 2-piece and after you look at it for awhile, get it on the right side, test fit each half and line up bolt holes bolt the 2 halves together and install like that.The mysterious round silver aluminum piece lines up with those 3 holes on the forward half. It does look pretty black in there so this could brighten it up.If one was so inclined, they could paint it, etch it, CNC a cool design on it then put it on. I’ll probably have my vinyl decal lady cut me a cool logo or something to put on it.

Yes they’re cheap, but I wouldn’t spend a dime on these. Look fine and do the job once they’re on but awful instructions and no necessary hardware. I bought these to replace previous liners so I didn’t have oem hardware. Overall terrible just spend a little more on something better

Drivers side installed in about 10 minutes the passenger took a little longer as I had to reroute my winch wires. Also the passenger side needed a little persuasion with a dead blow at the front. Was a body man by trade for 20 years and I’m used to things not being perfect. I think any complaints are from people that don’t understand that jeeps are mass produced and so are these inner fender wells by a different company. I would not hesitate to buy these again especially if you don’t want the silly designs that are cut into other companies products.

Great value! Was worried at first but got these and they fit very well. I painted them with bed liner. Easy install as well.

Did not like the instructions, but they were better than most. I had to go to the hardware store to get something to make them actually fit. I only used four of the screws and nuts provided. I think it looks good overall, but would have gone with another selection if I had more knowledge of what I was getting. I don’t want this to be negative. I just am being honest. I have a rear set coming next week and then I’ll be able to see if they’re similar or better.