Aidelife Dust Shroud for Angle Grinders, Universal 115/125MM

Made of good quality plastic with some metal fittings and a brush around the base to facilitate better dust extraction. Comes with 2 tools to tighten its clamp and one for the angle grinders blade, several sizes of collar attachments aiming to make it a universal fit, and a dust extraction adapter.Fitting, easy enough although, specific adjustments maybe required for what ever machine you have, in my case I needed 2 M14 spacer to allow the blade to be correct height to reach the surface.Prepping hallway floor for tiles I find a high spot up to 4mm which I need to reduce, hence the purchase...Connected my old Bosch grinder to a vacuum via a cyclone, and so pleased I did as there was a lot of dust for a small area. The blade guard has a slide opening allowing close use to edges of floor, when using this function the dust extraction doesn't really work which is understandable...For the price of £25 I think this bit of kit is excellent, however, for a professional and constant user I'm not sure how long the kit would last?

It was a bit fiddly at first but when I found the right washer and tightened the bolt up a bit it did fit quite snug but also allowed me to rotate the cover around the grinder when I let the quick release go. I’m planning to use it with the rubber disc with fibre sanding pads as seen In the photo, it also comes with washer to hold the disc flush with the shroud. I haven’t tested it yet too see how well it collects the dust but so far I’m happy with the purchase, this is the second Aidlife attachment I’ve purchased and they seem well made at a good price too.

I couldn't fault this product. I found it easy to fit and it took 3 -4 kilos of unwanted material into my dust extractor in a couple of hours allowing for breaks and emptying the extractor. I was working indoors and attached to an extractor had no clouds of dust and very little mess. Great product.

I bought this product to smooth down a hump I had on a new concrete slab that was laid, it stretched about 2ft wide by about 11ft long. I'd bought a grinder disc and wanted the shroud to cut down on the dust. It fitted to my Screwfix hoover lovely but the issue I had was fitting the shroud. What a nightmare, I needed to fit one of the collars but it required quite a lot of brute force. The best thing I found was to remove the clamp and use force to open the neck until one of the collars fitted. It was also very difficult adjusting the height of the shroud so the disc touched the floor and the bristles of the shroud just covered it. Overall it greatly reduced the dust but didn't eliminate it. A word of caution if you can set up a cyclone bin in between the hoover and the angle grinder, do it! My hoover filter became clogged after about 10 mins, and ended up cleaning it at least 4 times before I finished the job. Overall it did the job but was not easy to set up and use.

i am a builder by trade and i can not fault this bit of kit could not believe how well made it is strong and sturdy and great value for money

Leave it well alone.

Removed old tile adhesive from concrete floor, to replace damaged tiles.Very effective leaving a perfect surface to take new adhesive & tiles.Virtually no dust ! Amazing!

Was not practical as it didn't really want to fit my grinder without it being too bulky.

I used this with a diamabrush cutter and a Bauer brand angle grinder to strip paint off my deck.At first I thought it wasn’t working because i didn’t notice a reduction in dust until one time I forgot to turn the shop vac on and I was covered in dust after using for a few minutes.So it’s safe to say that this thing helped considered I wasn’t covered in dust from there on out when the shop vac was running.Occasionally a big paint chip would clog the vent but for doing light sanding it definitely helped reduce the debris on my deck afterwards. But it’s not 100 percent going to reduce dust, there will always be some left. But overall it helps.Good tool addition for the price, came with plenty of adapters and fittings to make it work on most grinders I’m guessing.

It was very difficult to set up correctly. Dust collection was not great. To work best, you could only apply pressure in certain directions. Otherwise dust comes shooting out from the sides

It was a bit difficult to install as it was really tight to get it around the adapter ring. The next size ring smaller was too thin and It wouldn't clamp tight. Nevertheless, I was able to get it installed and it did serve it's purpose. Can't imagine there is a grinder this won't fit on because it does come with quite a few different adapter rings and it should also fit just about any vacuum because it comes with different rubber adapters for the vacuum connection.

I was worried when I made the order but when I installed on my craftsman grinder and connected with shop vacuum I finished removing a concrete layer of the basswood with no dust . I like it .

This shroud fit great with my Makita 7" heavy duty grinder, the additional adapters makes for an easy install, durable and inexpensive.