Koala Printable Clear Sticker Paper - ONLY for LASER Printer - 8.5x11 Inch 20 Sheets Full Sheet 100% Transparent Label Paper for DIY Personalized Decals, Labels

great quality sticker paper. I use on my HP laser color printer; I have no issues with it going through the printer. I made a mistake and wanted a sticker for a glass block. It was a beautiful, printed sticker, but it did not work as I wanted because of the transparency on a glass see through block.

These clear stickers worked flawlessly with my printer and produced sharp, vibrant designs. They adhered beautifully to my candles, giving them a professional and polished look. Highly satisfied with the quality and ease of use!

Very good results when using with the laser printer. Clear crisp images.

Using a Brother MFC-L8600, set to print on label paper at high quality, printing a single sheet at a time from the multifunction tray, I had the following experience: • The first page jammed. Opening up the back, it had gotten all folded/wrinkled up on itself, like it became ultra-floppy when heated up. • My printer has a pass-through mode for use with envelopes, where you flip a pair of switches and leave the back of the printer open as you print - it avoids the paper making any large turns. I turned that on and printed again; this time it printed without any difficulty. I laid the label sheet flat and put a box along one edge to keep it from curling up and let it cool for a few minutes. • The vast majority of what I printed adhered extremely well. However, some - but not all - areas of solid intense red had adhesion problems, particularly the ones closest to the edges of the page. My layperson's guess is that the solid high-saturation red resulted in lots more toner that needed fusing to the sticker-paper (since it's 100% Magenta + 100% Yellow), and/or that the heat from the fusing drum might be a touch less strong near the edges for some reason. The red stickers still came out OK for my purposes - some were entirely fine, others lost edge details, others had some of the toner in the solid area rub away leaving a much lighter color - but I'm not selling them. Other solid colors didn't have this issue, and the problem was lesser or absent further away from the edge. • Cutting the sheet was easy. • Peeling the sticker off the backing wasn't too bad, but making sure it didn't immediately adhere to my hand was a little trickier. • On the destination surface, the adhesive stuck well, but I could pull off a sticker I'd mis-aligned. (This often but not always resulted in it not looking *quite* as nice on re-application, though not terrible.) • The clear portion is pretty clear - not 100% invisible, when the light's from the right angle it's easy enough to see the edge, but from other angles you just notice the design, and there's not an amber background. I haven't used other clear labels, so can't say 'better/worse' than others, but these ones are definitely at least "satisfactory". (As of use - I don't know if clear labels yellowing with age is a thing that might happen or not.) I'm going to be more careful about areas of solid color and try and keep the amount of toner in those areas lower (by not using 100% saturation, by using hues that don't mix multiple colors of toner, by turning on toner-saver mode) and see how that goes. Other than that one problem and a slightly more involved printing process, these worked great.

Works perfect and makes great decals.

This is a great product. It was easy to use and looks great. I cut it on my Silhouette machine (watch their tips and tricks for machine cutting before you start). I can see reordering it very soon because I will use it up fast. Wish they had a 50 pack.

The only brand I use for clear stickers, perfect with the paper quality and most important it's water resistant. All my bottles hold up well in all types of coldness. Perfect thickness as well.

Printer did not like this cutting machine did not like it and it wrecked my cutting mat because it would not come off. I used the lightest grip mat for this and it stuck and wrecked it. This was horrible. Will never purchase again

Ok paper should of read properly I just assumed was normal a4 size but was not

You need to make sure you set your laser printer to transparency or the toner won’t stick properly. Once you have the right settings, it’s as good as your printer allows it to be. Images are vibrant and clear, and the toner doesn’t rub off. The thickness once you’ve peeled the backing and applied is nice and thin. I’m using to add graphics to Cornhole boards. Trick is to apply one layer of polycrylic (or whatever finishing you are planning to apply, apply the sticker, then apply the rest of the polycrylic layers. I would buy again and have been.

Súper práctico tener reste tipo de hojas puedes hacer mil etiquetas del diseño h tamaño

It works perfectly with my Brother laser printer. Just make sure to set your printer's Setup to at least "Thick Paper" and you're good to go. Prints perfectly, espcialy since I need to custom-create transparent labels for a birthday giveaway. I'll be order this again for future projects.

La impresión no sale bien (no es para impresora láser como anuncian, aún siguiendo las recomendaciones de configuración de impresión). Mi impresora láser imprime perfecto en otros papeles adhesivos, vinil, clear sticker paper, etc. y en este que compré ha sido el peor resultado. Quise probarlo por el precio pero es tirar el dinero a la basura. No lo volvería a comprar