CPG224 Air Distributor 5/16", CO2 Manifold - 4 Way

This manifold was exactly what I was looking for and worked wonderfully. I purchased a full sized kegerator from a friend with the idea being that I would use the kegerator for dispensing homebrew. Most homebrew batches are 5 gallons which means that I can store, easily, 2 5gal kegs in the kegerator but I only have room for one CO2 tank. The manifold works to allow both kegs to carbonate at the same time.When it arrived, I used double sided foam tape and two small screws to attach the manifold securely to the inside of the kegerator. I would suggest using air line specific hosing, and follow the diameters exactly. When done so, it does take some elbow grease to attach the line to each of the barbed fittings. Although, technically not needed, use some hose clamps as well.I used this manifold in conjunction with Ball Lock style connectors which does allow for additional sealing when one connector is not hooked up, but the ball valves attached are great for closing pressure while initially connecting the air line. The ball valves do not act as regulators, and should not be thought as regulators. Instead, they simply open and close pressure to the line. To regulate one line independently, you would need to have a separate regulator on the line.Eventually, I may upgrade with independent regulators, but for now I am very happy with this purchase.

My CO2 tank is plugged into a 4-way manifold. Two are open for things like purging fermentation vessels, kegging, etc. The other two go into my two kegerators. Inside each kegerator is a 2-way manifold going to the two 5-gallon kegs inside. Just make sure to spray with something (star-san, water & soap) and make sure your connections are tightened down completely. They are a simple, intuitive design and they just work. Great value.

Decent quality, sturdy mounting points, valves seal as advertised, would buy again

I just received this today so time will tell, but so far I am very satisfied. I had only read the other reviews after I purchased it from Draft Warehouse via Amazon, it arrived today only two days after my order was placed with standard shipping. Upon opening the package I partially disassembled the manifold by removing the inlet barb and end plug to check for any oil or metal shavings but I saw none and a rag ran through the body of the manifold came out clean, I don't know if mine was from a different seller than others who were complaining of theirs being dirty, but mine was clean and ready to go out of the package. Other reviewers had mentioned there being cleaning recommendations shipped with theirs but I did not have any. Anyway, I applied a bit of RectorSeal #5 to the screw fittings I had removed, attached my CO2 line and submerged it in a water bath to see if there were any leaks. None. It is now installed so I'll update if I notice any leaks or longevity issues, but so far this looks like a great bargain.

I purchased this CO2 manifold when converting my single tap kegerator to a double. After reading the online reviews I was a bit skeptical due to complaints with metal shavings and leaks, however 1 year later everything has been working fine so far. I didn't take it apart and clean it when I first got it, but only due to pure laziness on my part. Probably not too difficult if I wanted to put in the effort. No leaks so far and for the price you can't beat it!

The product arrived quickly and was packaged well. The fittings were notacebly wrapped with thread tape and were screwed in tight. I soaked the entire manifold in saintizer for about 15 mins and no noticeable dirt or oil came out. I just installed it into my kegerator, which was alot easier than I thought. I used clamps to tighten everything and there is no leaks! Happy with the product so far. I got mine from keg works.

I bought a Kegerator and it only had one air line entry point in the back of the unit. All the research I did indicated that it is best to keep the CO2 tank outside the refrigerator to prevent condensation inside the tank when moving between warm and cold temperatures.I didn't want to drill any additional holes and violate warranty so I bought this splitter to feed both kegs on the inside of the Kegerator. So far, it works as you would expect.

Very quick shipping, works great and no problems. I only gave it four stars because I think they should send the unit disassembled for easy cleaning. There is a lot of oil from milling, as well as shavings inside. I am using this for beer pressurization, and sanitization is paramount. I highly recommend taking this completely apart and cleaned with some type of solvent to get all the oil and shavings out. Kind of a pain in the butt. Once it is cleaned and hooked up, test for leaks. Everything works well and I am happy with the purchase.

Build quality is great, I sprayed the whole thing down with soapy water and didn't see any leaks. Its been hooked up for a week now and I've not had an leaks.Its really cleaned up the c02 lines in my keggerator and made it look much more professional

Excelente producto y calidad, ya instalado en mi Keezer Casero para dispensar 4 lineas

I grabbed one of these co2 manifolds to help setup a friends beer brewing room and since Bev Rite is a well-known brand I bought this without question.Right off the bat when you hold it, you'll feel that solid weight as it’s a nice fat tube of aluminum so the walls are pretty thick. Just like with anything that deals with gas to check for leaks first. So what I did to check for leaks was to plumb this up to just an air compressor, turned off all the taps, throw it in a bucket of water and gave it a couple dozen psi.I didn't have any issues with the valves they were spot on however the end plug was letting a bit of bubble out. Disconnected the compressor, dried off the valve, removed the end plug, cleaned out the old sealing material (looked like pipe compound), gave it a few wraps of a nice teflon tape.Hooked everything back up, threw back that psi level and it held just fine.I gave this 4/5 stars as it is a great value compared to local prices. It would have been 5 stars if it were not for that end plug issue. Kind of annoying BUT an easy fix.TIP ► For safety such things should always be psi tested first before you use it for your intended purpose as it is just so easy to do. This is a good rule of thumb to get into a habit. Yes, anything brand new 'should' work just fine however we cannot 'see' a gas leak as we can with water. At times lost cylinders of co2 gas can be prevented by checking the connections first.TIP ► Cannot throw something like this in a bucket of water? Then make a soap solution and brush that over all the joints. If you have a leak you'll see the bubbles form right at that exact spot. Always check gas related products !Helpful, is how I hope you find my review

Producto perfecto, no presenta fugas, funciona correctamente

I've had this manifold for over a year and it has drained my 5lb tank 3 times!!! Very disappointed.