dephen5V USB LED Light Strip 4.9ft, 480LEDs Warm White Dotless COB String, Flexible and Cuttable Rope Lighting, CRI 90, Self Adhesive Tape for TV Backlight, Cabinet, Bedroom, Mirror, DIY

Added a couple of rows of lights to the bottom of my monitor to light up my desk with this. Nice, soft light. Bright enough. Powers up to the previous setting. I don't need to use the inline controller much, just set it and forget it. The adhesive made it easy to install and even with a 180º turn to make two rows it keeps sticking nicely.

Exactly what I needed. I can easily plug or unplug it from the USB port on my 3d printer to get a better view.Good adhesive, easy to cut to size, and very bright.Its also a nice bright white without too much blue light. I've had a problem in the past with cheap led lights having a blue tint when they are advertised as daylight or white.Also good to note that all the pictures were taken with no other light sources in the room turned on.

Used for lighting 3D print project Dr Who TARDIS windows and top sign backlighting.A) they measure and work as advertised. Measures about 1.8mm height.B) love the . 49" cut spacing vs others at 1.5"C) soldering leads to pads after cutting was easy with a little practice.D) tried resistor and buck converter to lower brightness to reduce heat at lights. Worked great.E) strip length was right, BUT both units I got had been soldered in multiple places, as if from scrap strips. Joints soldered WELL, but I don't like the adhesive backing being the only thing holding segments together in many places. I think other sellers will have same thing though.F) adhesive backing holds VERY well. I had to remove a strip from model. It readhered well enough that I was surprised.G) if you will be enclosing them there by trapping the heat, definitely use reduced voltage. 3v still plenty enough bright, but no significant heat buildup. All the other comparable brands with similar specs to this COB strip have the same power consumption at rated voltage.After using 2, I ordered the Pautix 2m strip in a warmer 3000k light. An extra . 5m for a dollar more.No hesitation recommending these to a DIYer

I needed 6ft but it'll do just fine ... it will be replacing a strip I had up for about 5 yrs... constantly on ... hopefully it'll last

Use these in light boxes 3d printed. They work well and can be trimmed to size. I use cheep phone charger for power and the run 24 7 will no worries about over heating the power supply or lights.

Used behind a 3D printed lithophane. It looks great. Nice, even light.

The AI bot was not helpful getting the light strip separated from the 3M 300LSE double sided high strength tape. When you roll out out the strip, a small piece at the end will be attached to the spool. If you can, preserve that separation. If not, slightly heat up the end with a hairdryer and use an exacto knife to carefully separate the brown paper from the lamp strip w/adhesive. Once started, its easy pull off the rest of the brown paper and expose the sticky strip light.The lamp brightness range is great and the control will remembers last setting so you may use this on a switched outlet. Using this 300K strip as a backlight for the television. A+

The media could not be loaded. I have purchased these for three different projects.The first was for a leg lamp to make it shine in all its glory. Worked perfect!Second arrived with the first section bad. If I moved it a little it would go on and off. Since I had already cut it to fit where I wanted to I figured I might as well try and fix it myself. Cut off the first section and re-soldered it back on. I’m using it for a custom under hood light powered by a Milwaukee M12 battery.The third string is for my tool chest and it works great. With a USB port already in the chest, it turns on whenever I flick the power switch for the outlets to work. I didn’t want them on whenever I had the power strip on so I ordered a usb switch and it works great now. With my garage lights off, in complete darkness, there is now plenty of light.Overall, I am really happy with the lights. The brightness is good, the color is good and the double stick tape is strong. Be careful when you pull the back off. I accidentally pulled one off from the wrong side and took the entire strip with the backing still there! Since it is so sticky, I was able to reapply it to the strip and was goo to go!