PrimoChill1/2in. Rigid RevolverSX Series Fitting - 12 pack - Dark Nickel

Thank you Primochill for giving me a huge reason to never but your products again.The design of these caps is incomprehensibly horrible. They are designed in such a way that you must screw in the fittings before getting able to get the caps off. Don't screw in the fittings hard enough and the entire assembly comes off. Screw them in just a tad too hard and you're never getting the fittings off again and there is no tolerance between the "sweet spot" and "too hard".Now I have a crappy fitting welded to one of my radiators. I can return neither product because desperately trying to get the fitting off has damaged it beyond the point of getting able to return it. All in these fittings have cost be about $150 to get NOTHING in return.I highly recommend this product if you're a sadomasochist. I really hope I can get these awful fittings off the rest of my gear, I haven't even tried yet.Thanks a lot, Primochill!

These fittings are pretty awesome, used with primochill 1/2 petg. Just cut the tube and prethread the collar then the o-ring, push flush into the fitting then hand tighten. Provides a serious grip and have not had a single leak that wasn't caused by user error. The provided tool is for removal of the collar, not tightening. After a few turns the compression seals the collar and o-ring quite secure, to the point that you aren't pulling them out. The powder coat is well done and sturdy, after a month or so still no flaking or residue on fingers. Also the collars are interchangeable, amazon doesn't sell just the collars but are a quick trip to primochill.com and you can find every color that they carry there. Instead of buying a new set I suggest grabbing about 24 of these then just grabbing the collar replacements from there. 24 may seem like a lot but once you get into watercoolong it would behoove you tto always keep some spares for bigger more complicated loop setups. Overall nothing really negative to speak of about these. Only word of guidance would be to take into account the full fitting width when loop planning to account for the thickness, make sure you have the space to turn them and to be gentle if/when using tools to not ruin that primo powder coat.

I have been doing my own custom loops for over a decade now, and this was the first time using the RSX fittings. Immediately I could tell these were miles better than any other fittings on the market. The sealing mechanism is dead simple, very forgiving, and almost idiot proof.Now let me say that I am not an expert at rigid tube bending: my cuts are not square, my bends are off and you can see the areas where i had to use sandpaper on the ends of the tube. My tubing looks good enough once assembled, but you can see the flaws of my workmanship in the details.But here is the great part: these RSX fittings don't care how rough your tubing is, how poorly it was cut, or if you have to coerce your tubing into the right shape with a bit of force. They just work. everything seals great with no leaks. I have been running this loop for a week now, and everything is perfect.as for useability: when you install the RSX fitting base, do it first before you install your blocks or pump. there is no place to get a good grip on the base, and you need to get them almost as tight as you can by hand. not ultra-tight, just a pretty good hand tight. once the base is installed on your pump/block/etc, then assemble your components into the case.once you have your tubing bent and are ready to finish the loop, the screw caps only need to be snug. install the tubing, make sure it seats into the fitting base (it will be obvious how it sits in), and then finger-tighten the caps. a little snug is all it takes to seal the o-ring. you will be tempted to over-tighten the caps but don't do it.that's it!last tip: the fittings are large, so make sure you have clearance. there is 1mm of gap between them on my EK velocity cpu block. close, but enough to work with.

I was worried about the color and how it would turn out. But this is such a piercing red it's exactly what I wantedThe fittings all seat well and the tools are cool. They sort of serve as torque wrenches bending when you've added enough force. Nothing leaks. Everything's easy to use. I'm glad I bought themAnd they're not as bulky as you would think. One of my concerns between these and monsoon was the possibility of them seating like big round doughnuts on the tubes. Not the case at all. See images below

These seemed pretty great until I was playing a game and the tubing popped of and sprayed inside my case. Luckily nothing got damaged, so I checked and a lot of the fittings were loose. This never happened with my EK fittings. I tightened them all, and reassembled. Reseated the tube fully and tightened it down.The next day the same thing happened. I am using them with Primochill's own hard tubing. The ends of the tubing seem to have contracted. This is pretty obnoxious, and I think my computer is damaged this time. Be careful.

Presentation wise they look amazing! Mine came with 2 sour patch kid candies which was a little weird but no worries. I also received them 6 days before they were supposed to arrive!DISCLAIMER: I didn’t eat the candy because I don’t trust packages with food in them but it was a nice gesture. 😂

I researched rigid tubing fittings for days. Primochill are not the cheapest but also not the most expensive. Very happy with the purchase. Just make sure to wear some gloves when you tighten these puppies down.. They will cut you if your not careful!

The media could not be loaded.  These fittings I've used many many times. Never leaks and looks great. Ive used red, silver, chrome, uv orange, and green on builds and they all look amazing!YouTube name: customgtpBuild name: Red Bull Mini Fringe PCCustomgtp Computers@RedBullFridgePC

Really wanted to give these a good review but really can't. The fittings are brilliant, well made great design and the colour is perfect. But it's all let down by the tightening tool which snapped on the first fitting so I had to use grips to tighten them and ruined all the paint work. Gutted but least they are physically doing there job

Great product