DC 5-120V 100A Volt Amp Meter with Hall Effect Sensor

Highly recommended! I have been using this product in my car for the past 11 months. I was hesitant to buy it because the price was so low, and because the current sensor would be in the heat in the engine compartment. The current reading seems to be very accurate, and the reliability has been flawless. The installation was a little difficult because 1) the wiring had to go through the firewall, and 2) the current sensor's ID was smaller than the battery lead's OD (a little filing on the lead made this work). I don't consider either difficulty to be the manufacturer's fault.

This worked extremely well to trouble shoot my Tahoe that was draining the battery. I was able to install it so I could watch what was going on over a week driving back and forth to work. ( turned out the onstar module was not turning off and over two days would drain the battery)

I was installing these meters (4 off) in a boat electrical system to measure the volts (circa 12 volts DC) and amperes (up to +/- 150A) in the charging and supply circuits (multiple batteries and charging systems). I used three 0-100A meters and one 0-400A meter. Unfortunately the 0-100A meters display 3 digits to one decimal place (stated accuracy +/- 0.2 Amps) but the 0-400A meter displays only two digits (unless the current exceeds 100A) with no decimal place so accuracy +/- 1 Amp. I could live with the accuracy but aesthetically the four meters, when mounted together, look a little odd; but this is only a cosmetic problem. When operating, the meters continuously take a small supply current so I ran all the neutral wires through a simple on/off switch so that I could switch them all off and avoid permanent current drain on the boat batteries. A more serious problem was the location of the selector switch hidden at the back of the meter and out of reach once the meter is panel mounted. I solved this by wiring a switch in parallel for each meter and surface mounting the new switches in an accessible position. Calibration is straightforward, however, once installed the only realistic calibration method is to ensure that zero current is running in the measured cable....this means that the wire for the power supply for the meter must bypass the Hall effect sensor. You need to figure that into your basic circuit design. Negative voltages are displayed not by a negative sign but by an additional illuminated 'second decimal point' at the end of the display reading. I'd prefer a negative sign but once you get used to it it is fine. The meter comes with an extended connector lead for the Hall effect sensor which I found essential for the installation. The voltage tails are short but extending them to suit the installation was easy and would have been necessary anyway. Overall the system, as installed, is working well and I have already been able to use the meter readings to trouble-shoot a battery failure that was previously hidden. Operating in a marine environment, I was careful to locate the meter panel in a well protected (dry and shaded) position; essential given the display type and the need to protect the electronics. Of course the meters have only just been installed so I cannot comment on long term reliability but so far so good.

This device is exactly as advertised, and instructions are clear. Some reviews say things like: "The instructions say to remove the current coil connection and then press the button until CCC appears and the unit is supposed to be calibrated." But that's not at all what the instructions say. The instructions say: "Take the wire out of the sensor. Or you can leave the wire in but make sure there is no current flowing through it.", Then it says "Press and hold the button for 2 seconds, then release the button.", Finally it says "It displays CCC on screen." There is a HUGE difference between "removing the connection to the Current Transformer" and "Taking the wire OUT OF the Current Transformer. Of course the CT must be connected for calibration. One must simply make sure there is no current flowing. Further the instructions DON'T say to hold the button UNTIL CCC appears, it says hold for 2 seconds, and release, THEN CCC will appear. Users will have no issues if they read the directions carefully, even if the grammar isn't perfect. My only disappointment is that the Resolution is only 200mA. It's a very useful device as long as that resolution is small enough for you. There are also three display modes: Voltage Only: Displays the power supply voltage. Current Only: Displays the current through the Current Transformer Voltage and Current: Shows one for a couple seconds, then the other. The odd thing here is that the current reading "flickers", presumably so that you know you are looking at the current. But it seems unnecessary, I'll bet that the current and the voltage aren't normally so similar that one can't tell the difference. A better approach would be to just flicker the decimal point or something.

This was an excellent meter for my Astron 20A power supply. I installed two of them because I wanted them to match. I also soldered a momentary switch to each of them so I could add the features of amps/volts /both and reset. This was easier than re opening the unit. I just tacked the external switch to the one on the meter. I tried other meters with the resistor and they caused me problems like low voltage. I recommend this one.

I wired in a refrigerator in the trunk of my electric car. (too many over buying trips to Costco) The refrigerator is very quiet and it’s hard to tell when it’s on let alone how much current it’s drawing. This handy little device lets me know. Large bright green digits for my old eyeballs. No current sensing resistor to deal with or cause a voltage drop problem under high currents. I took advantage of the included extension cable for the Hall effect sensor, but had to make another one for the DC power. The button on the bottom works fine to switch between the voltage, current, volt-current display modes. I only monitor current though. I did use the zero calibration for the current feature. I also did some bench tests to see how accurate the measurements were. While not important for my application they were within specs.

This little meter is pretty basic but performs as designed and described. I use it to monitor the amp draw from a 12v bank of lithium batteries but it can be set to monitor voltage as well, or both at the same time. To monitor both voltage and amps though, you will have to tolerate the meter constantly switching back and forth from one reading to the other. This meter only provides real time information so dont expect it to keep any type of record of your power usage. Also, if you install the donut the "wrong" way, the meter will still show your amp usage but will signify the reading as a "negative" by placing a decimal at the end of the number showing on the meter. For example, if you are pulling 100amps through the line that the meter is monitoring, the meter will show "100" if the donut is facing in the "proper" direction. If the donut is not facing in the proper direction, the meter will show "100.". Do you see the distinction there? Just a simple decimal dot. Or period. Or whatever you'd like to call it. Bottom line is that its hard to mess up the installation of this little device.

GREAT LITTLE UNIT WITH CURRENT DO-NUT. Works great; easy to install, stable electronics, even has an extension cable to remote the donut! WILL BUY AGAIN!!

Bright and accurate display. I used this to replace battery charger amp meter. I was worried transformer might interfere with pickup. No issues works fine

Tiny, very accurate, easy to install and use. Interesting price for the product qualité.

They,re very good. I like them.

Very good shows the amp very well and the volts

This is the second one that I order and the 6.5 foot cable is missing as per the description