Racor PBS-2R Two-Bike Floor Bike Stand

Used in my garage as an alternative to always placing my bikes against the wall. Works perfectly and installation was quite easy as well.

Este soporte para bicicletas es la opción ideal para todo aquel que busca una solución de organización de calidad para sus bicicletas.El rack de piso es de gran calidad, materiales fuertes y resistentes y en verdad ayuda a maximizar el espacio. El ensamblado es relativamente fácil y no se necesitan muchas herramientas – Se tiene que tomar en cuenta que al ser un stand fuerte y resistente habrá que apretar algunas tuercas y no será una solución 'out of the box' o lista para usarse, pero vale la pena invertirle los 20 o 30 minutos necesarios para ensamblaje por la calidad que aporta.Aparte de ser una solución perfecta, los terminados son altamente estéticos; El recubrimiento negro mate del metal es resistente a ralladuras superficiales y provee un gran acabado que sin duda es un plus a una solución que solo por la calidad de sus materiales ya vale la pena.

Good price and quick delivery of this item. It came nicely packaged in a box with all the pieces protected in plastic wrapping. Instructions are minimal but adequate. Once assembled, this stand holds my two recreational bikes with 700 mm tires end-to-end (Option 2: bikes in opposite direction) very well. This stand would not work with bikes in the same direction due to handlebar interference. Most reviews that rate this product low are due to assembly difficulty. You must be patient and not get frustrated when assembling this stand. Due to the design using pipes and tubes (i.e., curved surfaces), alignment can be challenging. However, all the pieces will fit together with no modification or extra drilling required. As directed, do not tighten the screws until all of them have been finger-tightened to hold the stand together. Keep in mind that the female threads on the tubes and supports are not the highest quality threads; therefore, some screws may allow finger-tightening all the way, whereas, others may only engage one or two threads. That's OK - don't be tempted to tighten them with the Allen wrench at this point. If you want to know how much thread engagement to expect on each part by just finger-tightening, try inserting and removing the screw before assembly. The main difficulty is aligning the screws with the female threads in the tubes because you can't see the threads once the tubes are inserted in the legs. Therefore, you have to get the screws started by feel. This takes patience! They will fit when everything is aligned properly, but don't get frustrated. Keep slowly moving everything around until the screws become aligned and engage the threads. Once all the screws and bolts are finger-tight, then tighten them with the wrench. Remember, you are not attaching a massive trailer hitch to a tow truck. The screws only need to be snug tight and the stand will work just fine. If you have problems getting the base to lie flat on the floor (not wobble), then stand on the tubular legs and tighten the square tube hex head bolts first. Then tighten the remaining screws in an alternating pattern (like lug nuts on a automobile wheel) while often rechecking the flatness of the stand on the floor. Just be patient and don't give up. Once assembled, the stand is a quality product with respect to the price.

¡Es un excelente artículo, como ya es costumbre llego a tiempo, no dudaría comprar otro igual, si viste otro artículo igual o estas comparándolo, no pierdas tu tiempo te aseguro que no te vas a arrepentir anímate! realmente cumple con sus especificaciones

I find it to be quite sturdy. It took a bit longer to assemble than I expected (approx. 1 hr) as it was a bit tricky to get it level horizontally and vertically. The instructions did say not to tighten the screws until you are sure it is level -- should have done as I was told! I will fasten this to a piece of wood (probably plywood) to put in the back of my pick up truck once I can get to the storage shed after the snow melts.Francis C.La Pêche, Quebec, Canada