Lian Li LANCOOL II MESH Performance - Black

Good case, no defects detected. Fits atx mobos and has fans included.

Tons of space, lots of outlets for wiring and temperatures are really low even with minimal fans installed

Quality case, good airflow, bit on the heavy side. Overall very good.

Great case. Moved my build from an older Corsair Air540 to this case in preparation for a RTX3090. Ambient temps in case went down 5 degrees celcius. CPU temps dropped 15 degrees celcius and the GPU (not pictured) dropped 8 degrees Celcius. Old case supported 6 120mm fans, 3 front, 2 top, 1 rear. This case supports the same number of fans, but at 140mm. Case temps listed above were with the 6x 120mm fans. The 3 fronts are now 140mm Corsair LL140 fans, the 2 top are Corsair SP120 fans setup to pull air from the radiator. The rear fan is a Corsair MP120. Pros: Excallent airflow Fits even the largest of ATX motherboards Multiple radiator mount locations both 120mm and 140mm. Front will support up to a 360mm radiator Pleasing to look at with or without lights The 3x 2.5 inch drive bay at the bottom slides front/back with a single screw attachement making for easy access to PSU cables. Plates on rear side make great mount points for additional fan controllers or lights Cons: Top USB 3.0 slots use a shared bus, so only 1 will operate at full 3.0 speeds Cable management in the back side can be tight if you are trying to keep it under the plates that hide everything. There is a handle/hole at the bottom of the front mesh. This allots lots of unfiltered air into the space. I 3D printed a cover for this. Current System Specs: Motherboard: ASUS Prime 470x-Pro CPU: Ryzen 7 2700x GPU: EVGA RTX3080 FTW3 Ultra Memory: 4x8 GB Corsair Vengeance Pro DDR4 3200

Easy case to install. If you like it black, this is a case for you. I think they have a white version. My Asus motherboard fan profile is very quiet with this case.

Best case I've ever had. Kudos to Gamers Nexus for working with Lian Li and improving on the original design. My temps are down 10 to 20° after moving out of my old Corsair carbide case. There is plenty of space for a large build. The internal mounting plates for 120 mm fans just below the GPU are what set this case apart in my opinion. The case is super easy to open, and the back panel has two cable management shields to make everything look amazing. I would advise not investing in the add-ons, such as the vertical GPU mount unless you have an all-in-one cooler. The vertical GPU mount does not fit with a tower cooler. The built-in fan controller looks simple but works great. 11/10. My case shipped from California to the East coast and took about 2 to 3 weeks but it was worth the wait. I was afraid that the glass might be damaged on arrival knowing my luck, but the packaging was solid. My only advice is to take care when unscrewing some of the internal screws. You can tell that they were driven in by a machine, I almost completely stripped one with my precision screwdrivers.

The case is great with a lot of nice features. However mine came damaged. The center mesh area on the front cover was pushed in. This did not happen during shipping as far as I can tell since the box was in good condition. I think it happened during assembly. They probably pushed against the center of the cover to install it instead of using the edges. I've already contacted Lian Li and provided them the information they requested but have not heard back from them yet. Like I said the case is great and was easy to build in. I added the additional usb c input on the top and had no problems with that. Update: After providing some information to Lian Li they have sent me a new front cover which should be here Friday. So great customer service for that. I changed my rating to 5 so if you're looking for a high quality case easy to build with this one is it.

Case was purchased with AMD recommendations in mind of using a AIO to facilitate cooling for the Ryzen 3950/5950x CPU. With the addition of (2) 140mm intake fans the memory and GPU benefit from an increase in airflow resulting in improved cooling. I am not sure I understand the logic of having glass on the back side panel.