LeMotech Project Box ABS Plastic Junction Box IP65 Waterproof Electrical Boxes Universal Enclosure Black 6.2X 3.5X 2.4 inch (158x90x60mm)（Pack of 2）

Great box. It unexpectedly included PG8 sized waterproof glands/strain relief and plugs. Quality build.

Awesome project box that was perfectly sized for the circuit and install that was planned. It was very easy to cut Acrylic panels to hold electronics because the listing had accurate dimensions! The thickness of the Plastic was great and the weathertight gasket provides a positive seal that has kept the build nice and dry and the electronics well protected! Included were high quality stainless steel screws that provide a a great look and will not corrode over time. I ended up fixturing it down to my cnc to carve holes to accommodate led holders. I scratched it during manufacturing and it buffed up nicely back to a high polish! This case has held up to the elements in the summer heat, rain and imagine it will do well in the midwest winter. I will be using these boxes in the future for many other projects!

I use such boxes for watertight connections on boats. This manufacturer happens to have many, many different sizes and configurations, and the one I chose fell right between two sizes offered by another manufacturer. In other words, the size (an oddball size) of this box was “just right”. In addition, this box is extremely well-made. It comes with a silicone rubber gasket to install on the lid to ensure waterproof integrity. Much to my amazement, it also came with FOUR cable glands, two each of a size, so any cable entering the box can be sealed off to prevent water ingress. The screws are genuine stainless steel, an important feature for wet locations. The 4 pre-drilled holes for mounting the box are each tucked in a corner, and “live” outside the waterproof section of the box so no caulking of the mounting holes is necessary. The 4 mounting holes are completely independent of the watertight compartment. Very clever indeed! There are 4 shouldered areas inside the box which will accept small (probably #6) sheet metal screws for mounting a terminal strip or other electrical items (relays, etc). It’s rated IP65 for water resistance, and I absolutely believe it. This rating means it is dustproof & can resist low-pressure jets of water (like rain or splashing water). I’ll definitely be buying more of these boxes in the future

It is exactly what it is and works as described. However .... The screws that hold the lid on each have a "column" in the box that extends to the bottom, using a lot of the internal space and I don't believe the dimensions allow for that. If you are installing a lot of different parts, they could all fit, but I could not use one particular part because of those "columns". Also, there are numerous stand-offs built into the base and its likely they are usable for some applications, but I could use none of them. They were not spaced correctly for me to hope to use more than one, and my standoffs were not the same height, so I could have cracked a board. I ended up drilling my own holes and using my standoffs. Of course, this left screw heads and tips on the outside bottom of the box which required me to add stick-on feet to keep those away from the mounting surface. I would like to see a part that is a standoff that I can glue to the box. I would screw the standoffs to my board, apply epoxy to the bottoms of the standoffs, and then set the assembly on the floor of the box and let the epoxy cure. The other annoyance that seems to be common is the user-installed beading on the lid to make a water resistant seal. How about a deeper channel and tube of some "goo" that I can squeeze into that channel and let it cure into a perfectly fitted flexible seal?

I made good use of this black ABS project box. It appears to have a good weather protection from its included seal too, which is just what I needed. I also appreciated getting some fittings included within the box for my low voltage multi-wire cord connections. I was able to drill several very clean holes for cabling, switches & LEDs and do some odd shaped cuts with my Dremel tool. It cut very nicely. No chipping or other issues that one might experience with a lessor (non ABS) box. This is the plastic material that is good for this sort of thing. I am quite satisfied as it worked beautifully for my project! I added this box to my Champion inverter so that it would be fully remote control via a series of RF relays all triggered by a simple 4-button key FOB. There are 4 different colored LEDs on the panel of the box with a push-button on/off switch in the center. Thanks to this box I can now control Start, Stop, Choke & Eco Mode and know exactly what is going on with it without having to go outdoors when using the inverter as a whole-house power backup for common winter power outages. I trust the quality of this box to safely maintain the integrity of my electronics and recommended it. Here are a couple of pics of the box on my new 'Wireless Inverter" project. (with FAT tires too. Oh yeah!)

I used this box to make a DIY fume extractor for soldering and it works exceptionally well. The box is sturdy and well built, but still easy to cut and drill.

Yeah, I like and use these boxes for various electrical & electronic projects. They can be drilled, carved & etc for any purpose necessary to integrate into a project because they're rigid but with some pliability, and tough too! I usually have a few around of different sizes. If an idea pops up, I check my supply. Possibly the best feature is economical pricing. This box also comes with two cord glands, and two plug bosses, with caps. Really great additions--especially for the low price. I'll certainly buy more in the future, (well, I'm 81, so . . .)

Everything they should be as a conduit box.

I used them for a small project, and they worked very well. The material is durable, and the finish looks good.

Took almost 2 weeks to arrive, but when it did the quality is amazing. Very strong and sturdy, seals nicely and did the job above my expectations.

このお値段で２つ付いているのはお得ではないでしょうか。 １つずつフィルム包装されているのでいいと思います。

Es básico pero de buen material, un poco delgado pero v su es resistente

近接センサーを小型基板に載せたものがあり、その埃除けのためのボックスとして利用した。 質感、精度、材質ともに満足。 2個セットだったので余計な買い物になったかと思ったが、1個目で穴開けに失敗したので、予備があって助かった。 今回、たまたま基板やプラグの寸法にぴったりのサイズの商品だったが、もう少しサイズのバリエーションがあるとなおよいと思う。