DROK 10K Temperature Sensor Probe, 5pcs 1 Meter Waterproof Temp Sensor Probe, Stainless Steel 3950 NTC Temp Sensor Probe, Digital Temperature Transmitter Extension Cable

We have had a Primo bottom loading tank water cooler for about 3 years. A couple of weeks ago the cold water stopped flowing. If I unplugged the unit and plugged back in after a few hours it would flow and then stop again. I came to the conclusion that the unit was cooling too much and freezing the line. After some online searches I found a YouTube video where a guy walked through a potential fix, which was replacing the temperature sensor probe and how he did it. This led me to purchase this pack of temperature sensor probes which have worked perfectly. If you are in this position and need to replace this probe on your Primo unit, your going to need the following: - These temperature probes - Electrical tape - Philips head screw driver - A long knife or blade Here are the steps to replace the sensor: - Unplug power to your unit - Unscrew the two screw at the top of the back of the unit - Pop the top off the unit and sit it off to the side - Find the black wire that connects to the board which terminates to a blue port - This wire will go into the side of tank which is surrounded by styrofoam - Use a long knife to cut a small section of the styrofoam out around where the wire enters - Slide the section out and pull the prove out - Cut the wire and splice in this new probe - Slide it back into the hole on the side of the tank - Put styrofoam section back into place - Put top back on and power unit on Such a great product an easy fix to a problem.

Worked great !!! Got my water dispenser up and running after 6!months

COMPATIBLE WITH ALMOST ALL BRANDS OF WATER DISPENSER, WAS ABOUT TO BUY A COMPLETE NEW WATER DISPENSER BUT THIS SENSOR GOT IT BACK WORKING LIKE NEW AGAIN , THANKS!

Worked perfect. Here's a tip, when you splice the wires, do not twist them all together. You need to split them in two and twist them separately.

Saw these as a fix for my water dispenser on YouTube and gave it a shot. It worked! Though I did have to cut and require the adapter. It was a great cheap fix rather than replacing the whole unit. Would get again but having the pack I doubt I'll need to.

Worked very well. I have a Primo water dispenser that would constantly stop working because the cold water would freeze up. This is the sensor that you need to replace so you don't have to throw out your water dispenser. The only tricky part is that I think the plug was slightly different so I ended up cutting off the plug from the original sensor and soldering it onto this one. Now everything is working fine :-)

I was forced to buy these due to the crap quality Primo water dispenser I own. It has a known issue where the sensor goes bad and causes the unit to freeze up. Saved me $400 by fixing my dispenser instead of having to buy a new one. Unfortunately, it isn’t plug and play. You have to do some wiring, but so worth it.

Works perfectly in our primo water dispenser once I shaved off the extra ridges of the connector

Bought these to replace the temperature probe in our water cooler. Was able to cut out the old one and splice one of these it. Works perfectly a year later and I have some backups in case it does wear out. A great deal!

Worked perfectly.

I bought these temperature sensors to fix my Avalon water cooler. I love my water cooler and hated the thought of spending more on another one. Found a video on YouTube to fix it. These sensor probes are easy to change and come at a great price. I highly recommend buying them as they work great. My water cooler is just like new. It's an easy fix. Why pay more.

Installed and it worked. Had to splice it into original probe wire as plug was not the same but no problem. Cheap and it worked so 5 stars.

Installed after following some youtube pros, it worked excellent. I have Avalon water dispenser and it is different little bit 5han most in those videos but the good thing the sensor connector fit right into the board . I did not have to cut and join wires so check your dispensers carefully before cutting following the videos.