VFD 220V 7.5KW 32A 10HP Single or Three Phase Input to 3 Phase 0-3000 Hz Output Variable Frequency Drive Control Inverter for Spindle Motor CNC Speed Control

I've got lots of VFDs. Recently one of them powering an older 5 hp Oliver table saw starting erratically not working at my ranch shop. I assumed it was a Mollom and emailed Jeff at Mollom about it. He immediately offered to replace it. When I actually checked the machine, it was NOT a Mollom, lol. So, I just ordered a new VFD for the saw, and replaced the big name VFD that was on it with a Mollom. Because of Jeff and Mollom's absolute standing behind their VFD's, I always try to buy them. Yeah, I could technically have gotten away with something smaller than a 7.5 KW for 5 hp. But I know the reason for the other failure, (jeff opined that it was a capacitor problem) was overloading the VFD when bogging down on a cut (The saw can run a 16" blade). We all know that Mollom doesn't have great manuals. But the Devices work very well and the service is impeccable. Any problems or questions, they answer the same day.

I bought this unit to replace an old and expensive VFD by MagneTek that was no longer manufactured. The MagneTek GPD 503 Model DS309 was going to cost over $1000 to possibly repair it and cost over $3000 new if you could find one. So I thought I would try this unit.Before purchasing this unit I sent a request to the seller with some technical questions and he responded in less than a day. After purchasing and receiving the recommended unit (model VFD 220V 7.5KW 32A 10HP) I asked for configuration information for my motor (230 VAC, three phase, 19.2 amps, 1755 RPM MagneTek motor in a commercial boiler system) and within less than a day got a response back from technical support with exact parameters for my motor. I connected it up and it worked, but the motor was noisy. Another message to support was quickly answered with the suggestion to increase the carrier frequency. I did so and the noise was dramatically reduced. (I increased the carrier frequency from the default of 4 kHz to 8 kHz using F0-15.) I then asked about terminal control of speed and quickly received a reply.Overall PROS:- excellent price/value- lots of configuration options for any application- flexibility- dual display- outstanding customer supportCONS:- no UL or CE listing marks- no cable/conduit management knockouts (I needed to cut a hole in the top to route control cables cleanly)- cooling fan runs full speed whenever the motor is engaged...noisy and make me wonder how long it will last.- requires time to get all options understood and set up, but support is very helpful.

El producto no sirve para la capacidad que especifica

This the 4th one of these we have purchased over the last few years. As of today we’ve had no problems with any of them or the machinery they serviceEasy to installHad a question regarding wiring with a braking resistor. Sent an email to support which was answered within 12 hours explains exactly what I had to do to achieve what we neededSo far so good……Would buy again

Worked with out having to change to many setting and does exactly what it should. There are a lot of setting and configurations. More options then one might know what to do with. The only thing that I was not able to figure out by reading the manual was the Single Phase wiring. They say to connect to L & N but those terminals where not there. I connected instead to S & T and it works fine. Also figuring out which of the parameters I needed to change to get more than 50hz took a minute to figure out. After that it works great and the soft start / ramp feature helps with my limited available shop amperage.

Worked fantastic, manufacturing support was very good

Used this to run a 80 gallon Ingersoll Rand air compressor with a 5hp motor that is for 3 phase power installed it and wired it up pretty easy struggled a bit on the parameters but contacted customer service and sent them a photo of the tag on the motor and they sent me back what needed to be set up on the parameters. They responded fairly quick as well awesome customer service

2 stars cause I cant use it still! I'm super frustrated the instructions say 3 phase goes to RST while single phase goes to L and N but there are no L and N inputs. If L and N goes to 2 of the RST, why wouldn't you say which ones???? I'm ready to send back just cause of this!!! The sticker says it accepts single phase input!