Big Horn 19408 High Pressure Glue Injector with 2 Brass Tips

So I purchased a DriTac repair kit and this injector kit together. The syringe and needle/injector that came in the box kit worked well for 8 holes (there was a bunch of air pockets in my engineered wood floor!), then it bent, was clogged and would no longer work. I switched over to this Big Horn product and immediately saw an improvement; in my ability to put pressure on the syringe, on the leverage holding the Bog Horn syringe/handle, and especially on the brass tips! It's important to clean out the syringe and tips, but this product rocks! The only thing I wish was different is I had purchased a much larger syringe. This will certainly work, but you may have to fill it multiple times to fill a large space. One other tidbit of info, it may be me, but I noticed I was able to get a much better flow when keeping the brass tip just a smidge off the floor. I was probably blocking some of the flow by pushing the brass tip against the floor a bit much, but once I raised it 1/32 or 1/16 from all the way in, the adhesive/floor leveling liquid flowed much more quickly. Highly recommended!

Works well. Wish it was a little finer applicator but robust enough to last

Very handy product when you are repairing barn wood which has a tendacy to have a lot of splits, checks, and cracks. I was hoping it had a tip with even a smaller opening but it works ok. (I also use a shop vaccuum to pull the glue through the crack prior to clamping them up to dry. )

I noted a bathroom vanity drawer with a horizontal split on the piece of wood that the side of the drawer. It wasn't completely split down the side but there was a noticeable gap. How could I get some glue into that space?This injector came to the rescue. I put some Tightbond III in it, squirt it in from the side, and put two clamps on the drawer side, letting it cure for 24 hours. It worked like a champ!Cleanup was very easy, just disassembling it to its component parts and rinsing them off in the sink with some lukewarm water.

Let me fully endorse the use of this glue injector for filling gaps under hardwood flooring. What a great technique! I installed bamboo flooring in our upstairs hallway and for whatever reason, in one spot the boards didn't get glued to the floor properly during installation. Walking over the spot was annoying because you could easily feel it under foot. It felt like walking on a trampoline!I drilled a tiny little hole near the center of the problem area, right on a knot, so you can barely see it. Then I filled it with wood glue using this injector. I was shocked at how much it took! Nearly an entire bottle of glue went into that tiny hole. I marked it off with masking tape so we wouldn't step on it for a few days and voila, worked like a charm! Feels nice and solid underfoot now.

Used this to fill voids in my floors. Warming the caulk makes it easier to inject. Takes quite a bit of effort to get the stuff into the void. The 1/16th inch hole ends up getting enlarged but I used colored caulk and the holes aren't very noticeable.The problem is with the screw on top and screw on handle. When you unscrew the top to reload, it's difficult not to also unscrew the handle. Biggest problem is with the threads on the cap. It's cheap plastic and the cap pulls off quite easily. Need more sturdy threads.While it worked ok, I'd probably try a different kind next time due to the design issues.

I was a bit skeptical about buying this as i wasn't sure how great it would work. I had some hollow areas under my hardwood flooring that were pretty annoying when walking over. All you need to do is drill a hole and inject a water based glue underneath...that simple. I used Titebond III Ultimate Wood Glue, 16-Ounces #1414. If there was one thing i could change about this is the size of the injector reservoir. Had to fill multiple times just to fill one void. Over all this thing held up and did as it promised and I'm completely satisfied. Make sure to clean it out immediately after use or there will be glue at the bottom of the injector that could be a pain to get at.

Had a couple of dips under my new hardwood flooring and had read about using a "hardwood flooring repair kit" that was basically a pressurized glue gun with a "special" glue. I bought Tightbond III wood glue off the shelf, drilled a super small hole in the wood, and used this injector. We taped off the area and didn't step for 48 hours and it's rock solid now. Using such a small bit and the small brass tip, I didn't even need to fill the holes because you can't even find them if you don't know where to look. A super high quality glue injector that I'll be pulling out for furniture repairs, etc.