76432 Class IV Trailer Hitch, 2 Inch Receiver Compatible with Dodge Durango 2011-2026 Model Years

Draw-Tite's long standing excellent reputation for fit, strength and quality was well represented in this application. Installation without any drilling was a treat and went smoothly. The process of installation on my 2019 Colorado followed helpful comments by others that the bumper needs to completely come off for ease of the bolt up and wiring tasks. I would add that the bumper was not easy to free initially after all bumper attachment bolts were out. To free the bumper, I found a solution by backing out all four bolts holding the original GM cross-tube to the frame rails until the cross tube had dropped down from the frame rails and had about a 3/4 inch gap. The bumper could then be tilted/extracted such that it's end plates that side mount the bumper to the frame rails would come free off the ends of the cross tube bracketing. (The bumper sat nicely on the cross tube's original ball mount support without any bumper attachment bolts in place, so no concern for the bumper possibly falling free during all of that cross tube loosening.) Draw-Tite eliminated that cross tube bracket-end interference and provides washers to tape to the frame that fill in as shims the free space thickness where the new cross tube omitted the OEM's interfering cross tube bracket ends. You can fully bolt up and torque the Draw-tite hitch to the frame rails and afterwards slip the bumper easily in place. I used a long breaker bar with a chain link fence top rail tube section as a cheater pipe extension on it to break loose the two of the (four in total) bumper side-mounting bolts that my 90 degree air hammer could not get in to reach. It was a lengthy effort to back out those OEM-threadlocked bolts, but no heat was required, just patience and endurance. After many years of installing frame mounted hitches from several manufacturers and front-mount tow plate bracketing for vehicles towed behind motorhomes, it was a pleasure to still be able to purchase another Draw-Tite product that continues the high standard you expect from a trusted brand.

Expected nothing less from Draw-Tite with this high quality hitch. Easy to install and they provide bolt fishing lines to assist. You will either need a second set of hands or use a hydraulic floor jack like I did to raise the hitch up. Took me less than 30 minutes to install and held up as expected pulling my medium sized trailer. Highly recommend.

Product is very well made with all the parts needed to make it work. The install is not extremely difficult on the Jeep Grand Cherokee L but it does require removing the entire fascia of the car. Make sure to have somewhere safe to put it so the paint doesnt get scuffed and blue painters tape for the seams. Doing the integrated trailer light wiring is strongly suggested while doing the hitch install.

I installed this on a 2020 XC60 T6 Inscription with little issue. There are instructions included with good pictures for the install, and good videos are found on YouTube as well. The only issue that I ran into was the mounting brackets for the bottom of the bumper need to be bent back out of the way and then back forwards in order to re-align. This CAN (was) done by hand but took some effort. You also need to trim about an inch out of the bumper, this is easily done with a utility knight (be careful) and you can follow the 'guide' printed in the inside of the bumper itself. Plan for an hour, but honestly, if I had to do this again, it would take 20min...

I bought this for my 2003 4Runner so that I could haul my car, and maybe eventually when I get dirty stinkin' rich, a boat. I have not towed anything so far, so at this time this review is solely on build quality and the installation. The package arrived pretty banged up, with tears all along the box. Everything was in tact, no missing hardware or instructions. This made getting the receiver out of the package very easy. The bracket that supports the towing wire harness was slightly bent on one flange, but not so much so that I could not attach the wire harness. All hardware and instructions are zip-tied to the receiver in a plastic bag. Instructions came in English, French and Spanish, and were printed front and back on an 8.5x11 sheet of paper (1 sheet for each language). This included instructions for both the Lexus GX470 and the Toyota 4Runner. The instructions were somewhat lacking, but with the exception of the handle bolts, the installation was pretty straight forward: Put bolts in holes. There were two minor setbacks: The aforementioned handle bolts, and the forward-most bolts. The handle bolts were SLIGHTLY bigger than the slots in the frame they were intended to go through, and the handles were difficult to manipulate. The slot being too small had a simple fix - GENTLY tap the nut through using a hammer. As for getting the nut to line up properly, good luck. The estimated installation time for this part was 35 minutes. I'm pretty sure I spent 35 minutes just getting the bolt threaded into this stupid thing - and that was only one of them. Hopefully you're more coordinated than I am. The issue with forward-most bolts was, like a few other reviewers, that the slots on the receiver didn't line up properly with the holes in the frame. The slots are about 1/8 inch inside of the holes in the frame (almost as if the frame was bent inward). Draw-Tite recommends putting the receiver in a vice and bending the flanges until they line up. What I ended up doing was, after bolting the receiver onto the frame, using C-clamps to get the holes to align. Some people mention needing a longer wire harness for their vehicles. I was able to use the factory harness just by removing the two separate harness plugs from the clips securing them to the firewall, and then cutting one additional tie down securing the harness to the firewall. The Receiver includes zip ties in case you want to tie them down more securely, but it was held taut enough for me. Lastly, I HIGHLY recommend wearing safety glasses for this. You WILL get dirt, dust and rust in your eyes if you don't.

This hitch bolts in easily to the vehicle it is designed for. The installation was fairly quick and simple with the included instructions. I would recommend watching a video if you are unsure of your mechanical aptitude. The item arrived days earlier than expected and included all the necessary hardware to install it. You will need a drill, a hole saw, and basic mechanical tools to install this hitch. It can be a bit tricky to bolt in to place if you do not have a helper, but with a bit of elbow grease and a few cuss words I got the job done solo. Highly recommend if you want to save a few hundred dollars over the factory setup.

Highly recommend this hitch. Was extremely easy to install >20 minutes. To make it easier lower the spare tire under your RAM with the provided tool which is located under the passenger seat. The main bolt that holds the hitch on is a 1-1/8 socket size which I didn't have so I picked that up and it went flawlessly from then on. The main bolt needs 260 ft lbs of torque. The two frame bolts need 110 ft lbs of torque. I used a 2' breaker bar and got those suckers TIGHT. Well worth the money, but install it yourself! It's so easy and will save you the installation fee at a shop. Cheers!

Purchased this January 2019 , read reviews and decided to try. Litterally took 10-15min to install in the snow. Very good product that came clean on time and with all necessary hardware. Installed on a 2018 Ram , and looks great. Definitely recommend!!

Unlike some other purchasers, my hitch lined up perfectly to my Tacoma frame with no issues . I fished 2 bolts through the frame with the wires provided. I was installing the hitch by myself so I used some wooden blocks to line it up & support it within about 1/2" of my frame. From there it was easy to insert & tighten all 6 bolts. Total install time was about 40 minutes with about 10 of that just getting the hitch on blocks & lined up.

Item arrived with damaged box but hitch was ok except for a small scratch, but hey, it's a trailer hitch! All fasteners were in a Ziplock bag and taped to the hitch and arrived fine. Used a 2x4 and my floor jack and lifted the hitch up and installed the bolts as per instruction diagrams. This hitch fits several different models so you need to pay attention to which diagram you use. The 3 holes per side that the diagram said to use lined up perfect but so did a 4th hole. I went to the hardware and got 2 more bolts and installed an extra one on each side. What the heck! The slight "V" shape of the main round beam of the hitch is perfect to allow the spare tire to fit with about 1/2" clearance. Installation total was about 45 minutes by myself. Couldn't have been easier! Very happy.