Liqui MolyCera Tec 3721 I Ceramic Wear & Tear Protection for Petrol & Diesel Engines I Smoother Engine Performance, Less Friction & Lower Fuel Consumption I Ceramic Additive 300 ml Pack of 1

LIQUI MOLY Cera Tec 3721 is a popular ceramic-based engine oil additive designed to provide wear and tear protection for both petrol and diesel engines. Here’s an in-depth review based on personal use, expert opinions, and user feedback:Composition and PurposeCera Tec is formulated with ceramic compounds that are intended to reduce friction and wear inside the engine. The primary aim is to protect engine components, extend engine life, and improve overall engine performance.Key Claims and BenefitsWear Protection: Cera Tec is advertised to form a protective layer on metal surfaces within the engine, reducing metal-to-metal contact and, consequently, wear.Friction Reduction: By minimizing friction, Cera Tec aims to improve engine efficiency and potentially enhance fuel economy.Temperature Resistance: The ceramic particles in the additive are designed to withstand high temperatures, ensuring the protective layer remains effective even under extreme conditions.Noise Reduction: Users often report a reduction in engine noise, which can be a sign of reduced friction and smoother operation.Application and UseCera Tec is compatible with all commercially available oils and can be used in both petrol and diesel engines. It’s typically added during an oil change, and one bottle is sufficient for up to 5 liters of engine oil. The additive is mixed with the engine oil and does not require any special procedures.Performance and EffectivenessPersonal Use and User FeedbackWear and Tear: Many users report noticeable reductions in engine wear over extended periods. This is often observed in smoother engine performance and longevity.Fuel Economy: Some users have noticed slight improvements in fuel economy, though this benefit can vary based on driving conditions and engine type.Engine Noise: A significant number of users report quieter engine operation after using Cera Tec, suggesting effective friction reduction.Smooth Operation: Improved engine smoothness and responsiveness are commonly cited by users.Expert OpinionsAutomotive experts generally acknowledge that ceramic additives like Cera Tec can provide additional protection against wear, especially in high-stress or older engines. However, the benefits can sometimes be marginal if the engine is already in good condition and maintained with high-quality oil.Pros and ConsPros:Enhanced Protection: Effective in reducing wear and extending engine life.Versatility: Suitable for both petrol and diesel engines and compatible with all types of engine oils.Improved Performance: Potential for smoother engine operation and noise reduction.Temperature Resilience: Maintains effectiveness under high-temperature conditions.Cons:Cost: Relatively more expensive than standard oil additives.Variable Results: Benefits like improved fuel economy may not be significant for all users.Over-reliance: Should not be seen as a substitute for regular maintenance and high-quality engine oil.ConclusionLIQUI MOLY Cera Tec 3721 generally lives up to its claims, providing an extra layer of protection for engine components. It is particularly beneficial for high-mileage or older engines and in conditions where engines are subjected to high stress. While the cost is higher compared to standard additives, the potential benefits in terms of wear reduction and smoother operation can justify the investment. However, it’s important to have realistic expectations and not to rely solely on additives for engine maintenance. Regular oil changes with high-quality oil and proper engine care remain essential.

TLDR: Makes all the numbers better.Because there is less energy being wasted due to friction. Gives engine oil a physical ceramic lubricant and a chemically bonded layer to all metal parts the oil touches, making the engine run with less wear and friction, saving a bit of fuel and repair bills.I have heard a LIQUI MOLY representative say that if you change your oil with Cera Tec then you can go 30,000 miles before the next oil change......................Maybe technically it is possible, but please no one do this. Change your oil every year or more if you do loads of miles.Update: I have put this in my new petrol hybrid.Small put noticeable mpg improvement.Noise reduction is more noticeable, especially at low and cruising RPMs.As the engine cuts in and out constantly due to hybrid system, the chemically bonded layer of lubrication definitely helps with the advanced stop start system. As there is always a layer of lubrication before the oil circulates.Peace of mind knowing that I have additional protection in winter and with short journeys.I had to buy something to suck out some of the oil before I added Cera Tec. The service was due in 4 months so I didn't want to bother changing it myself. Service has to be done by a dealer to maintain warranty, but you can change it yourself between that if you want. I don't put enough miles on it to justify a 6 month oil change.When they change the oil at the dealer I will lose the ceramic physical part, but the chemically bonded layer will still be there and lasts about 30,000 miles. I will put MoS2 in when they change the oil to bring back the physical part.I put this in my older diesel and a petrol car. I also did an engine flush in both. For best results do it with an oil change, do it yourself or get it done for you and then add it. My car needs 4.5l of oil Cera Tec takes up 0.3 so I put in 4.2l of oil and then Cera Tec. Pro tip, when you have poured in the bottle, put some oil the bottle and shake to get the most out of the bottle and in your engine.How it works: There are 2 parts to it. The first is the "physical" lubricant element which is ceramic based hence the name. LIQUI MOLY also sell M0s2 which is a physical particulate lubricant, but Cera Tec is more advanced and modern. Think of the physical element as another layer of lubricity that rides in the oil film so you have 2 layers of protection between the metal parts of your engine. Castrol use liquid titanium as their physical part in their oil to improve lubrication but the concentrations are not as high as a dedicated oil additive. This part works as soon as you put it in with the oil.The ceramic physical part also helps a lot with reducing the heat degradation of the oil. Ceramic has great thermal properties and this will keep the oil film at its best for longer.The second and more important, unique and noticeable part is the "chemical element." Cera Tec has a chemical that will bond to the metal components of the engine that the oil touches, leaving a bonded layer of lubrication that will last up to 30,000 miles. Meaning you have 3 layers of lubrication in the engine instead of just the oil film which degrades over time and usage.The chemical part takes about 500 miles of driving to work as it needs heat and pressure to form on the metal surfaces. You can probably speed this up with a few motorway trips at mid RPMs. Once it has, you will notice the difference!!!Here is what I have noticed:5mpg improvement. Most people find a 1-2% improvement in fuel economy which over 10,000 miles a year adds up!Cold starts sound a lot better.It helps reduce engine wear from short journeys.Power delivery is smoother and the car feels happier to rev.It has made my diesel so much quieter, I would even suggest buying this just to help with the "diesel tapping" sound.The engine just sounds better and is so much quieter at lower cruising revs.Engine start up is much smoother and quieter as there is a layer of lubrication at all times even before the oil starts to circulate. This may help prolong starter motors as well as it can crank the engine with less effort at cold start up.If you had a fast car that can take corners at speed your engine could experience temporary oil starvation which can cause a lot of damage, but with Cera Tec, you have that bonded layer of lubrication to save the engine in rare circumstances like this.When you change your oil next you will lose the physical ceramic lubricant, but the chemical layers lasts for 30,000 miles. So just buy LIQUI MOLY M0s2 for the 2 oil changes after Cera Tec to bring back the physical part.Remember don't buy Cera Tec for every oil change!!!! Or your wallet will hurt. Use Cera Tec once and then the next 2 oil changes should be done with M0s2 and then back to Cera Tec for the 4th. (If you change oil every 10,000 miles and or once a year)Change your oil just before winter and use Cera Tec, your engine will thank you. Remember it will take about 500 miles of driving to experience full benefits. Worth every penny.