SCRIB3D P1 3D Printing Pen with Display - Includes 3D Pen, 3 Starter Colors of PLA Filament, Stencil Book + Project Guide, and Charger

Amazing, works great. Use it everyday and works perfectly fine still, after two months i can say still going strong and look forward to further use.

What a great little 3d pen. Works well uses both filament can change this on the pen. Can have hours of fun with this. Three colors came with the pen, needs to be plugged in when using, can use a power bank with it though. Daughter loves it and had done some great designs. Easy to use and comes with a little book of simple templates

The product itself is great especially for the price. You can create nice models with it but it has a couple flaws that occurs with most. The pen occasionally stops feeding the plastic through. This will seem like it is broken but take the plastic out and cut off the plastic that seems a bit thicker. The surface matters a lot. The design sheets provided seem to be the best to draw onto as they stick to it enough to keep a shape but not enough to take the paper with it while peeling off. The pen does not fully stop when you want it to. Due to the heat and pressure inside the pen, the plastic will spill out a little bit more and many fine plastic strings will come off your build. Make sure to have scissors handy to remove these. Switching colours makes waste. Some of the plastic last used remains in the pen after ejecting it so be sure to drain it before adding to your build.

Great to use (as my daughter says) and I was amazed at how good the end product results turned out

The printing pen works well & I bought a project book to go with it for my Grandsons birthday. He loves it.

My son got it for Christmas. Was easy to work out how to get it going and he learnt quickly how to operate it (he's 10). I've seen some reviews saying it worked at first and then stopped working but he's used it a few times and so far so good. The filament that comes with doesn't last long so recommend buying some extra.

Dreadful. Broke the first time we used it. Very disappointing I wouldn’t recommend. Better to buy a properly ‘branded’ product elsewhere. I wouldn’t recommend definitely not recommend this for children as it has small parts on it which can easily get lost, rendering the whole product completely unusable.

This might work better for a patient adult but for my 9 year old was difficult to use. It’s a bit complicated to get the hang of and to change colours. It gets really hot so can’t use it for too long. She has used it a handful of times since Christmas so wasn’t really worth it for us. Takes a while to heat up and get going too

Good quality for money. My kids love it. And they made many things. The only issue I faced is that it didn't work once I got it out of the box. I had to open the pen using a screwdriver. The pushbutton was a little bit displaced. I had to readjust it. Not everyone can do the same. But it worked for me.

Amazing for creative kids

Excelente lápiz de 3D

This is probably going to be the most in-depth review I have ever wrote on Amazon. I am doing this because I feel like it is important for when you are shopping for 3D pens. This will cover the PLA that the pen comes with, and also PLA I bought elsewhere and why I have chosen what I have. ------------------- My first impressions: I am surprised at how light the pen is. I have small-ish hands for a 5'1" woman and it felt very comfortable to hold. After reading the instructions, it states that if the PLA crackles or bubbles while the using the pen, to lower the temp. Sure, no problem right? Not really. I use wax paper to trace my designs on, I use this due to a youtube video which suggested it, and its a lot cheaper than the mats. I also prefer it over mats because it is paper thin, which gives me the most accuracy of my tracing which is important to me. I started using the pen at the default 190f. As I was using it, I noticed that the PLA did crackle in the pen, and it did form bubbles. As advised by the instructions I turned it down lower. The lowest point for PLA is 160f according to the instructions, however, it would not stick to the wax paper at all. I then tried 170f and again, the PLA would not stick to the wax paper as well as it had with the 190f. Once more I turned it up to 180f, it stuck, not as well as I would like but it was a lot better than the other settings. Also, at the lower settings it gives no time at all to adjust the plastic if you need to nudge or squish down a bump. Changing the PLA: After using most of the PLA given in the kit, I went out and bought from a local small buisiness (SUPPORT THEM!) which uses locally sourced PLA. Once more, I tried the 190f temp setting. Not only does the PLA come out much smoother, it sticks to the wax paper perfectly, and I am noticing my pen does not get near as hot using it. I can use it for much longer before deciding to give it a break. This means I can nudge the PLA, and bend it and it sticks well to my wax paper so it does not shift on me while working. I also notice that it is much less stringy than the PLA the pen comes with. PLA brand matters, and it is good to research into a good PLA, I am just glad our local PLA works this nicely. TIPS: Bonus, a tip to enjoy your pen even more. You can get a lot more use out of your pen with various other tools. A wood burner with temp control and multi tips is wonderful for shaping and smoothing your project after you had made it. Use aluminum foil covered in painter's tape to fill in big gaps to use less PLA. A course sand-paper followed by a smoothing sand paper also helps in finishing off the nice smoothness of the PLA. As stated before, Wax Paper is a wonderful material to work on. It could be used repeatedly until it eventually tears and painter's tape peels off it nice so you can adjust and move it. Look for some good youtube videos to get you started on techniques to best build your 3D Pen creations! Overall: This is a very nice pen for its cost, you can adjust the temp, its light and comfortable, also easy to use. Pictures provided show the projects I have made with this pen for my D&D sessions. The PLA that I bought works wonderful for being painted right on without any primer. If you are curious, I use 3D Fuel PLA. Someone suggested not to work it too hard, giving it a break every 30min or so, I think some times I do go closer to an hour. Always press the up button and get your PLA fully out before you turn it off (by unplugging it). Always trim the tail off the PLA. I have yet to run into any of the issues of it clogging or just turning off. Only twice did it seem to "turn off" and I think my PLA had nudged the cord since it curls, because it would auto go back to temp after.

Molto carina e ben fatta. Mia figlia ci si diverte molto è anche veramente semplice da usare consigliata