Rev-A-ShelfCabinet Door Mount Kit for Kitchen Base Cabinet Organizers, Pullout Storage Shelves and Drawers, Trash Cans, 5WB-DMKIT

I just finished installing these in seven of our kitchen cabinets as icing on the kitchen remodel cake. Really tired of getting down on the floor to pull out the heavy mixer or juicer from the back in the bottom of a dark cabinet. UPDATE: 1 year and all units are working great. No issues.Pros: Nice chrome finish and fairly sturdy. I would have preferred the Rev-A Shelf birch wood units but too expensive for our budget. These are reasonable in comparison. Assembly of the unit is about 10 minutes.Cons: Installation took a couple hours for the first one. Maybe 20-30 minutes for each additional unit. Some things were not obvious. See tips below.Several assembly screws easily snapped off. Glad there were extras.My experience:The units are 1/2" smaller than the cabinet opening. I ordered for an 18"w cabinet opening and the unit is 17.5"w. That allows for clearance for protruding door hinges. The instructions said to mount the unit away from the door hinges (off center in the cabinet) which leaves a 1/2" gap on the hinge side. That side just stands in the air unattached or anchored. Being off center bothered me. I would need to add some kind of blocking to move the units to a centered position.In my case I also ordered the door mounts to convert the doors from hinged to a pull out configuration.That's where my confusion started. The door mount brackets were off center from the doors position directly below the drawer because the units were installed off center. I didn't have enough door frame to mount the door that off center. There are round discs (spacers) included with the door mount bracket kits that will allow you to move the brackets left or right but it looked odd to me.I realized that I could use the round discs (spacers) to center the whole unit by using the spacers in between the unit frame and the door frame on either side. The four spacers provided at the four front anchor points. I had to provide longer screws to make this work. The result was a centered unit in the cabinet opening with a centered door pull. See pictures of the spacer positions.Tips:1. Hand tighten the assembly screws. They snapped easily with a screw gun, even with the drag set low.2: If you are installing the door brackets (separate kit) use the spacers to center your unit in the cabinet opening rather than off center. See pictures3: Install the drawers so that you are sure the brackets that attach to the back of the cabinet are truly parallel and won't bind the drawer slides. Mark the holes, remove the drawers and mount the rear brackets. Then attach the unit to the bottom/base with the four screws provided.4: Mounting the door to the brackets: Attach the brackets to the bottom drawer. Tighten the screws just until the brackets stay in place but can still move if pushed with some force. Apply the the double stick tape to the bracket faces. Pull the drawer slightly so that it just sticks out beyond the cabinet face. Line up the door panel under the drawer face right to left and also the door top down from the bottom of the drawer face. Press firmly in toward the brackets so that the brackets adjust from the pressure and the double stick tape adheres to the door panel.. Carefully open the door/drawer and attach the screws.Note: The instructions said to face the brackets outward. This did not work for our doors so we turned them inward.

Easy install, sturdy, and good quality!We remodeled our kitchen and bought this hardware with the trashcan set and we are super happy with it!

Good product. Pricey for what it is, but this isn't all that surprising for a one-time purchase product. Bought this for use with a trash can slider (Rev-A-Shelf RV-18KD-18C S Double 35 Quart Sliding Pull Out Kitchen Cabinet Waste Bin), and installed both at the same time to ensure alignment would be right. Install was a piece of cake and didn't take any longer than suggested in the instructions, maybe less. No problems with the wood screws or double-sided sticky tape others have mentioned. Some have mentioned that it was a problem that the door brackets extended beyond the cabinet frame - this is not a problem as long as your door covers the brackets, and it will not interfere with the door closing all the way. I made one minor adjustment to the door brackets to adjust for tilt top to bottom - I did this even before I put the door on because I could see the angle would otherwise be wrong. Stuck the door on with the tape and made one more minor adjustment for height (I actually did this by unsticking the door and resticking - the tape was strong enough that I actually had a little difficulty unsticking it). And done. Works perfectly. I would only suggest one improvement to the instructions, which is that you'll need a small wrench or plier to hold the stop-nuts which you screw on the L-brackets - a small plier would be best based on the slider frame that, in this case, will otherwise get in the way.

Instructions called for about a 20 minute install. It took me a little longer as I’m a tad OCD and broke out a level and took my time making sure the door was right before installing the bracket. The double sided tape is a nice addition to help hold the door in position while your line things up before mounting but I would count on it for more a one position adjustment. Thoughtful though. All and all satisfied.

Attaches in-cabinet to any basket slide-out the eliminates the need to open the door first, then pulling the slide-out. Simply closes both is one move, very convenient!

Be warned though you may have to flip the brackets around to make it work but it works so well.

The media could not be loaded.  Bought the combo trash can pull out (32qt) and door attachment Rev-A-Shelf brand. And both were super easy to install. Feels durable. Love having the bigger trash can under my sink.

The media could not be loaded.  Shelf is easy to put together and install. There are these crossmember bars that look like they should snap and completely, but simply don’t. And from time to time they come loose and pop off which they can easily be snapped back on. The bins look like they’re slightly too big for the Unit as I show you in the video, they tend to overlap each other on the top lip. Another little thing that can be adjusted however, it is annoying to me.

Merci

Buen acabado pero no se adapto a mis necesidades, con relación a los insumos empleados en la fabricación, el precio si se me hace excesivo.

I highly recommend this accessory! I love being able to pull open my garbage/recycling cupboard. Well made and sturdy!

La descripción es confusa, yo pensé que era toda la parrilla y solo es el kit de instalación. El cual son 4 placas y tornillos. De hecho no la use.

A real gem with the Rev-a-shelf trash containers. No touch, no mess system. Feeling ridiculous to say, but I enjoy my garbage bins so much! :D