RUSTINS Quick Dry Varnish, Clear Matt, 500 ml -Fast-Drying Water-Based Wood Varnish; Durable Non-Yellowing Finish in Gloss, Satin or Matt for Indoor Use

I used it to varnish some oak that I had been working on. Used on top of a wax which I sanded lightly then used three layers of varnish as instructions and has left a nice dull, clear shine to the wood , highlight the grain and colour of the wood.

I have used this varnish to protect some wood I painted with emulsion paint. Goes on very well and dries quickly. It has given an extra level of protection to the painted area.Clean brushes with water tin will last an age. Very pleased.

This product is not matt - it warns you on the tin that it must be stirred to incorporate any residues at the bottom of the can otherwise it will be gloss. I stirred, stirred again then stirred even more - guess what - it’s still not matt. It’s somewhere between satin and gloss. As it turned out, the shinier finish is fine on the piece I was using it on. It’s also very easy to use and it levels well. It dries quickly and appears to be very tough - which is a bonus.

I wanted a finish for an elm board that wouldn't darken the grain. I thought Osmo would be good but it made the close-grained areas very dark, more like mahogany. Dulux 'diamond hard' was OK for colour but left a surface that didn't sand well. After reading the reviews for this Rustins product I bought it and did some tests.I have an innate suspicion of water-based varnishes as not being proper varnish, just a patsy to EU directives where a good product has to be replaced with a not so good one. But the reviews were right. When first applied to bare wood the wood does darken, but then lightens over the next 30 minutes almost back to how it started. The tin says 'quick drying' and as others have noted, it's really a bit too quick, as it starts going tacky in about a minute. So work fast.Being water based the first coat brings the grain up, so fine sanding is needed. This can be done after two hours. The surface sands easily ether by hand or with an orbital sander. After the second coat the wood went darker as before, but then didn't lighten so much as it dried. However the elm is now a pleasant medium golden-brown colour.I think two coats will be enough, just in case it gets darker with every coat, then a very light sanding and finish with wax polish for a nice lustre.So far no problems with getting the tin lid off and on again. I suspect this is because people leave it off too long and residual varnish dries on the bearing surfaces.

Seen some people saying they don’t know where they went wrong etc. with all these varnish matte/satin/gloss you have to lightly sand in between coats and don’t don’t don’t go over the same bit twice that’s how u get white bits and mix till your hearts content before using also use a sponge brush leaves best finish :) here I’ve used matte one on fireplace and satin one on drawers and gloss one on cupboard . Lightly sanding between coats. I use a heat resistant paint underneath it leaves an opaque flat finish whilst not disturbing the wood grain underneath. Rustins heat resistant paint. Kitchen cupboards radiator drawers fireplace it will never chip and looks fab works on anything with virtually zero smell dries flat always never bunches or streaks either. Those small drawers I did 8 years ago with this varnish on top (satin one) and still like new other pics I’ve just done recently. I never change the items I use because they function fantastically together! I always give “real”detailed reviews because I always need them too! and I get frustrated when I cannot see something I like or want how it uses or works before I buy so I do the same for others. Because I know what it’s like.

In my images the shots with the sun on the bureau is before and the video and other shot is after.The finish before was ultra matt but now I would say it is a satin finish. At night it looks matt and during the day and in bright light it has a sheen to it.I don't mind the finish as this is going to be a high traffic piece so it needs the protection.The application was super easy and simple, I used a foam roller as I tested a synthetic brush on the back like the tin suggests and it left strokes. The foam roller application was super smooth.It dried in around 10 minutes, but it is a warm day and painted it outside.If you're looking for a matt finish this I don't think is the product for you, but in-between matt and satin, this is perfect.You don't need a lot of product, I used half a tin but that's because I did two full coats.I would use this again, but for a more matt look I will trying something else.

Great product. Makes the timber pop.

This varnish is super easy to work with. Actually used to varnish "in" some vinyl stickers (numbers one to 100 with gridlines) so that youngsters (4 and 5 years old) in a class room environment could not so easily peel things off. This will definitely help - however it does not seem like a rock solid varnish which might have been a better choice for this particular application. That said - it goes on well, coats evenly pretty easily and the end product is pretty good. Washing brushes - simples - under the tap.

This stuff is rated (in UK - not sure the U.S. has an equivalent standard) to be safe for baby toys. Meaning my grandkid can suck on the side of his rocking horse without getting sick or toxic chemicals in his body.And the rocking horse looks really good. I'm very happy with it!

Me encanta, seca rápido, acabado muy bonito, satinadoLo volveré a comprar

Pas d'odeur, application déroutante Car laisse une traînée blanche (qui disparaît avec le séchage)Sec rapidement,aspect très légèrement vernis.Parfait

Joli couleur naturelle et protège

Bon vernis mat, pinceau facile à nettoyer à l'eau.Livraison rapide, article conforme à l'offre.parfait.