Never Fall Complete Sink Repair System ™

We just installed these on our under-mounted, stainless steel, double kitchen sink yesterday and I am impressed. Our home is 12 years old and the sink has been dropping in front for some time now. We tried tightening the existing clips but it didn't last, which brought me to research solutions when I found these. Before fixing it, there was a 3/8-1/2 inch gap in the front of the sink, for reference. I'm not sure of the limits of the brackets, but they were able to close our gap. Our sink was mounted with 4 clips held up with screws that are placed in slots milled into the underside of the granite countertop, and a glue/sealer between the sink and granite. This may have been adequate if not for a garbage disposal and the fact that the cabinet has a little hinged utility drawer in front of the sink making it impossible to support it in that entire area. That noted, we couldn't use the center mount that was included with this kit either, but the two side supports seem to be doing a great job by themselves. These parts are very sturdy and made well, IMHO. I was impressed with the weight and heft when I unpacked them. There is "peel and stick" glue-tape on the mounting brackets to hold them to the cabinet wall after you place them and before you screw them in, which is a huge help in installation. It's still a task with many frustrations, mainly from lack of accessibility under a sink with existing pipes and a garbage disposal, but we managed to mount them and tighten everything together after the caulk/sealer was applied. Hooray! It looks like a successful project completed! Fortunately, our double sink was a tight fit in the cabinet and the walls were close to the edges so the angle for mounting these was pretty ideal. We were able to fit the braces between the original clips and tighten them up as well so, hopefully, the combination will be adequate to support the weight even without the front sink support. There are other options that I've seen in my research, if needed, that could be added, like a brace under the disposal or sink basins. I will update my review if there are any changes or failures with this kit. I would strongly recommend it at this point and, if you're a DIY-type person, that you would be able to install it yourself. Otherwise, I'd advise a handyman's assistance. 5 stars at this point!

I normally don’t write reviews but this product is so perfect for an undermount sink fix repair. The turnbuckle design allows for tightening after the brackets are in place in order to raise the sink up after the new caulk is in place. No helpers needed this is an easy one person job. Also the slim design means cabinet space is not really impacted by these being in place. I was able to leave my cabinet (sounding organizer etc) entirely as it was with no adjusting needed. Was really good to have a well designed solution and made the job so much more easy to complete. My sink is more solid and secure now than it ever was with the original install :)

I have a large double bowl stainless steel sink that fits very tightly inside a 33" sink base cabinet! It was dropping down quite a bit, (at least 1/4" gap showing) especially on one side, and created a big crack in the granite counter in front of the sink as well! My granite installers had just used some scrap pieces of wood nailed to the sides of the cabinet to hold the sink up, and over the years a bit of the wood had rotted a bit away. The sink was dropping lower and lower. I googled for how to fix a sink, and saw lots of "how to " videos involving complicated repairs requiring the sink be removed, etc. Then I saw the you tube video for this product, the " and saw a you tube video for this product, the "Never Fall Complete Sink Repair System" and it was like a miracle answer! Voila! I bought the product and then could NOT get my husband to ever find the time to install it. Then today I had a plumber over to do some other repairs and asked him if he could install this system and fix the sink. The plumber was fascinated by this product and almost seemed excited to try it! He said that they do get a lot of calls to repair bottom mount sinks that have fallen, but never had heard of this product. He installed it in no time and had my sink caulked and back up under the countertop very quickly (important when you are paying an expensive plumber by the hour, LOL!) He was very impressed with the system! I am too, and highly recommend it. It even works in tight spaces, as you can see in the photo. (BTW- the turquoise blue in the upper back is a very leaky dish soap dispenser, in case you are wondering!)

### Five-Star Review for the Never Fall Undermount Sink Brackets I recently installed the Never Fall undermount sink brackets, and I couldn't be happier with my decision! Initially, I was just looking to prevent a potential sink disaster after hearing about a friend's mishap, but this product truly exceeded my expectations. The design is incredibly user-friendly. Simply turning the shaft of the turnbuckle pushed my sink back into place with ease, without the need for any drilling into my countertop or removing plumbing—an absolute game changer! It’s perfect for tight clearance situations, making the installation process stress-free and straightforward. Professionally made by a granite fabricator, these heavy-duty brackets boast an impressive capacity of 680 lbs. Patented and built to last, they provide unparalleled support for all types of sinks, from cast iron to stainless steel. The fact that one kit is usually sufficient for an average fallen sink is just icing on the cake. Each turnbuckle effectively replaces two supports, so you end up with five solid points of reinforcement—talk about peace of mind! The installation was a breeze. I simply inserted the double-headed sink bracket, peeled the double-sided tape off the wall bracket, and pressed it into place. The temporary adhesive allowed for hands-free operation, making it easy to secure everything with the included screws. I loved how quickly I could raise my sink into position by just turning the turnbuckle—no more awkward contortions under the sink! One tip: if your cabinet wall is exposed, make sure to measure the thickness before using the provided screws. I found that matching them with slightly shorter screws from my local hardware store worked perfectly, ensuring I didn’t break through the other side. It’s these little details that make the difference! With the Never Fall system, I now have the reassurance that my beautiful new sink is securely supported. It comes with a comprehensive instructional manual and a helpful video link, which made everything even simpler. Plus, the lifetime warranty adds an extra layer of confidence. If you’re considering enhancing your sink’s stability, look no further! The Never Fall undermount sink brackets are a must-have. Trust me, this system will never fail you! Highly recommended!

Woke up one morning to my sink laying inside the cabinet below it. After much research, I chose the Never Fail Complete Sink Repair system. Being a 66-year old female, I was concerned about 2 things: 1) ease of installation and 2) durability. I sure didn’t want to have to do this again! When the product arrived I was happy to see it appeared to be high quality manufacturing. Reading the instructions—which were thorough and easy to follow—led me to believe I could do this alone. Except for the part where the sink needs to be supported while the adhesive dries, which is not actually part of this support system. But I’ll tell you how I addressed that, in case any of you are in a similar situation. After more reading, You Tube-Ing, and searching for stand-ins for the clamps I didn’t own, I copied the suggestion of one man and kept the sink in place with duct tape!!! Worked like a dream. The supports of the Never Fail System went on with ease after the adhesive dried. Then came my favorite. Part of the job...when I pat myself on the back because I did it alone! I’ve had the Never Fail system in place for 6 months now and there have been no problems. But I knew that would be the case by the time I’d finished the job. The design of this great system is brilliant and doesn’t require the use of epoxy like some of the others. I can’t praise the company who makes this product enough! It’s hard these days to find products that 1) do what they claim, 2) provide quality workmanship re: the parts, 3) supply instructions that are sensible & easy to follow, 4) are free of useless gimmicks and 5) have been designed simply but effectively. Bravo to those behind the Never Fail Complete Sink Repair System! I hope this review sends you more soon-to-be-satisfied customers.

This system is the the most elegant approach I have ever seen to sagging undermount sinks. After days of cuss words trying to repair failed wood blocking unable to bear the weight of the disposal unit pulling the sink down from the countertop -- and still more days searching in vain at building centers and hardware stores for a solution -- I took a flier on this and boy am I glad I did! The components are well made (e.g. the edges were bead blasted so they don't cut one's fingers) and work pretty painlessly. The double-sided tape on the lower brackets is not all that strong, so I found it best to have a screw on the tip of screwdriver handy to "tack" the unit in before finishing the remaining screws with a cordless drill (carefully set to lower torque to avoid blowing out the cabinetry sides). Overall, the installation is quick and painless and works as advertised. I loved how you can turn the turnbuckles by feel alone while watching the silicone caulk bead compression from above, to make sure everything is even and perfect. The design and quality make this one of the best home repair purchases I have ever made. It's a real gem of engineering. It took me from misery to happiness in short order, and I truly praise this product with unbridled enthusiasm!

I do many detached kitchen sink repairs and I've used 5 different versions of under-mount brackets. So far, these are the fastest ones to install. Because the wide mounts do the job of 2 narrow ones, it saves time and effort. The ratcheting clamp for the front is genius and worked great. You will want a long extension for your driver, and the smallest (narrowest) drill/driver you have to drive the screws in the gap between a double bowl sink. If you have a single bowl sink, I don't think you'll be able to install it. There is plenty of adjustment room on them, so if your sink has a gap, you'll be able to mount the brackets first, then push the sink back up into place. Slight cons: -It would be nice if the turnbuckles were hexagons so you could fit a wrench on them. But I just used pliers and it worked great. -It would be really great if they could incorporate a spring into the extension that pushed the bracket arm inwards toward the sink. When the gap between the sink and the side of the cabinet is small, you have to hold the bracket against the sink when you tighten it to keep it in place or it can fall over and away from the sink flange. It can be difficult to have 2 hands up in place under many cabinets. -It would be awesome if self-drilling screws were included in the package. I usually replace the included screws with self-drillers because they go in much easier.

Our under-granite sink was slowly pulling away on one side because it was installed with these stupid flimsy steel clips that push against a routed slot in the granite itself. They're not only a complete PITA to tighten, the granite has terrible tensile strength meaning those routed slots break and the clips have no purchase. I was trying to brainstorm a bracket to fix things when I did a search and found these. These are a bargain. They're very sturdy, very simple and much better than the competing products. They are not only stronger, they have many degrees of freedom, swiveling a bit at the top so that if you are stuck pushing up against a clip (rather than flat between them, for instance) that's no problem. You can also mount these without having to have them perfectly vertical because of the swivel. Once tight they will press evenly and firm up just fine. They're easier to remove if necessary because of the pins, easy to tighten by hand, easy to lock with the jam nut, and easy to mount because of the adhesive. Now I don't have to worry that a heavy pot of water or overzealous cleaning lady is going to collapse the sink into the cabinet.

You are looking at this review because very likely your kitchen sink fell. I found this product on Amazon, copied and pasted its name in youtube and was sold in less than 2 minutes! We loved everything about this product. A product I would never forget and the aaaawwwwwwwww will never end. Highly recommended to everyone. We are fascinated by the idea. Extremely thought out! This is the best 'repair' product I ever bought if not the most useful ever. Package arrived in less than 24 hours. The product is solid. The set up was straight forward easy. The sink is back up! Soooooooooo tight!! Can't see how this product would fail. It works!! MIRACLE PRODUCT!! One of very few products that does the job and does it beyond perfection!!! Fabricators for Fabricators - You guys know what you are doing and teaming up with Amazon!!!! Thank you!!

Fitted this to my large single sink which is sat under a stone worktop. Was relatively easy to install and has given me peace of mind. The sink is going no where.

Brilliant, fixed my issue and easy to install.

Works great and saved me from having to spend thousands on a new sink/countertop. Been installed for months and no issues. Was easy to install and is of very high quality.

Worked exactly as advertised. Easy to install and adjust.