By applying pressure from the side, rather than from overhead, the In-Line Clamp stays out of the way as you work. A peg that fits into any 3/4" diameter hole holds the clamp in place, so the In-Line Clamp makes it possible to get more from any bench with dog holes—or any work surface where you can drill holes. The In-Line Clamp also makes a perfect companion to the Kreg Mobile Project Center. The In-Line Clamp gives you the helping hand you need, when you need it, with the versatility and power you want for a wide variety of do-it-yourself and woodworking tasks. The clamp applies up to 250 lbs. of clamping force and swivels to clamp from any angle on almost any shape work-piece or assembly. Pack of 2 In-Line Clamps.
R**N
Love these clamps...
One of the best investments I've made when it comes to woodworking tools. I love how versatile they are. And I am surprised how much clamping power they have. While they are strong, you can over toque them, so you do have to be a little careful.Last year I built an assembly table and I set it up with 3/4" dog holes on 4" centers. It has worked out so well. I have never had a time when I couldn't use these clamps. They work perfectly for 4" on center tables, just slip them in and go. Also my table is 1-1/4" thick, so they fit thicker tops..I use them to tighten my face frame joints before I put in pocket hole screws. Last night I used them to hold down drawer boxes so I could flush trim the bottoms with my router. They did not move at all. I've lost count how many ways I've used these.Only very slight negative is they do not have hold down power, and some times they push a work piece up. Not a flaw, just the nature of the design. But I usually use clamps to hold pieces down, so they don't lift.I have like 8 of these now and often glad I have every one of them. Will probably be picking up more in the future. You can never have enough clamps, right?Highly recommend.
E**X
Love these things...need more!
These are being used in a Shapeoko III CNC router wasteboard.Strong, hold their grip and reach around the worktop surprisingly well. I was skeptical when I ordered these. After all, the are just plastic. Upon arrival I discovered that they are larger and much more robust than I anticipated. They functioin with very little flex and hold tightly enough to keep the workpiece where you put it. When extended, there is a small bit of upward deflection which can raise the piece off the table just a touch, so just use a modest amount of care when placing them and you should be GTG. I'm picking up a couple more today, matter of fact.
K**5
It Works
ease of use and it was not expensive, i got 2 of these to use on my work bench table along side my kreg bench dogs.they work flawlessly, if i had 1 thing to change i guess it would to make the dog legg a little bit longer..maybe 1/2 in. or less.I am useing these on a work bench of 3/4 plywood with a 3/4 in. mdf on top of that, it work just fine.holds my boards for sanding, or card scrapeing, or useing my hand planes.TY for a great product......and now off to play with them nd see how long they will last and hold up GOD Bless the U.S.A
B**E
Impressed with quality
A bit pricy but they simply just work - fit my 3/4 dog holes and now I can get sanding and other chores done faster and easier -and for me that is key as it makes my shop a.k.a. garage time much more enjoyable - even fully extended these will hold your stock rock solid - then they retract easier then my clamps I used to use - pop them out and they are easily out of the way and simply pop them in the dog hole for use - the corner notches I have not used but Kreg thought of everything by adding them
M**N
Not bad at all - was going to get the festool ...
Not bad at all - was going to get the festool inline clamps, but now I might just use these. Works in the Kreg portable workstation as well as the festool MFT type holes. Very good band for the buck if you already have some dogs and have 2 different sized holes.
N**T
Bench style clamps!!!
These clamps arrived earlier than expected! Thanks to the seller! My tables are old and only had 3/8" dog holes from lomg agao. I just added a few 3/4" holes for these clamps to fit in. They work great. I love the kotches on th flat ends so I can use the clamps on an end of a picture frame like project. I will most likely buy a fe more. I have many other Kreg clamps and these new ones work well with eveything else so far! I reccomend anyone buy at least 2 of these to add to your collection of bench style clamps!!!
W**
Did the job
I bought these to use with my CNC . I think they work great. My spoil board is different than most as I use milled 2x6 boards between the struts and drill 3/4" holes for the clamps to fit into. This gives more than 1" of depth for the clamp rods to work in. With that they work great, I bought one pair and then bought another. They have a long reach and hold well. I have not had a problem with pushing the work piece up as some have mentioned but I do watch for that.
J**E
Good buy
Great product for how simple it is. I haven't used it yet for sanding. I like the low profile. I did clamp down a board and it felt plenty secure for sanding or routing a sign.
ترست بايلوت
منذ شهرين
منذ يومين
