3D Printer Enclosure with LED Lighting Constant Temperature Cover, Medium

I've been meaning to get an enclosure for ages, as my printer sits near an HVAC vent and I know that doesn't help prints. Temps vary wildly in the basement too, and I'm sure that isn't helping. Finally pulled the trigger on this enclosure. The medium size is HUGE and has more than enough room for my Ender3 Pro. Assembly was straightforward, and didn't take too much effort. Directions were good. Just make sure you fully seat all of the rods into their sockets and you shouldn't have any issues. I found it easy to assemble the frame and set it on the floor, then slide the the cover over the frame, versus the directions saying to try to drop the frame into the loose cover. It's a snug fit, but it went on with no problem. I was able to zip-tie my webcam to the frame, so it didn't need to sit on the stand that I printed for it anymore, which is a nice space saver. I need to clean up some wires and make things look nice inside, but it's a great enclosure that should help me get more clean and consistent prints. It also cut the fan and printer noise way down, which is great! My only small complaint would be the light bar - it puts out enough light in there to work, but I feel like no matter where I've tried to move it, it's just not quite right with my webcam and Klipper. I see they sell additional lights, so I may buy one, or just design and print some other kind of solution. Other than that one small thing, which isn't worth knocking the product, as it's a personal preference, this enclosure rocks!

I was skeptical of buying an enclosure for my Ender 3 V2. I have my printer in the basement and was open to the idea of having an enclosure to keep the draft down and temperature controlled. It was easy to put up, is sturdy and made with think fabric that is good material. I had it up in less than 20 minutes. My printer fits perfectly in the enclosure and the quality of my prints has increased significantly. Stringing has stopped and the edges of my prints are crisp. I would recommend this to anyone that wants to increase the quality of their prints. I don’t have the ventilation add on, but it is nice to know when I start printing ABS and other materials that I will be able to keep fumes contained and out of my house. The light is bright and works well to light up the area, but I will probably buy another to keep the quality of my webcam. Overall 5 star product!

I needed to reliably print a few parts for a Voron 2.4 build, which requires ABS. I have an old Prusa I3 clone in the garage which I've occasionally used for this since there are usually no drafts, and I stink up the garage instead of the house. During the hot summer months, when the garage is often pushing 90F, I'm normally able to get away with printing ABS well with an open frame. Come fall and winter, warping becomes an issue. Plus, the family was getting tired of the "Don't open the garage door!" exclamations from me when I was printing ABS. Picked this up to provide a quick enclosure, with hopes it would allow reliable ABS printing (and allow the garage door to be opened while doing so). This has worked SHOCKINGLY well. Since my printer has been in this enclosure, I've been able to print about 10 parts, a few of which are highly prone to warping (small contact space on the bed). All of them have printed successfully and beautifully. Of course, the blast of "ABS stink" when you unzip it to remove the print is fun. "Just the facts, ma'am": Pros: - Super easy to assemble, although it's bigger than you think so have some space. - Canvas with the shiny fireproof lining is thick and well sewed. It didn't feel "cheap" at all. There is quality here. - I find the LED to be plenty of illumination, especially since it reflects off the shiny material inside. My print camera finds it to be plenty of light, too. - A good number of round bungs to route cables through, that seem to be in the right place. Two on the back and one on the right-hand side towards the rear. - Has a rather large flap on the left, which I'm not using. Closes with velcro. - I like that measurements were listed clearly, so I could ensure it would fit and get the correct size. Medium worked for my Prusa I3 clone (about the size of an Ender 3, I guess) with room to spare. - I can print ABS consistently, and get strong, clean prints! Cons: - Bungs are a little on the tight side. Had to really push the power cable through and thought I was going to tear the fabric. I did not, which is also a pro I guess, that canvas is pretty tough! - The clear viewing window has a lot of folds in it, so it can be a little difficult to see print details. Overall, I think this is a fantastic value if you're looking for an inexpensive and plug-and-play enclosure for your 3D printer.

The enclosure works great for my ender 3 v3ke but the light that came with it was missing the clips to hold it on. It was easy to assemble and came with gloves since the rods for the frame are fiberglass so be sure to wear the gloves it's really sturdy and holds the temperature in which makes for better prints. I'm only giving four stars because of the missing light clips.

Highly recommend. Having a good enclosure around your printer will improve it's reliability tenfold. My prints don't shrink away from the platform any more. This enclosure does a good job of holding the right amount of heat in. The LED light is super helpful.

Bought this for my Anycubic Kobra X. Measured the 3d printer to pick out the right size enclosure. The Medium is the perfect size for the Anycubic Kobra X with the 4 spools of filament at the top. Setting it up was extremely quick and easy. There are 3 sets of sturdy pvc pipes that you connect together to make the frame. Then you drop it into the actual cloth enclosure. The LED light has 2 metal clips that you clip on to the light and it clips to any part of the frame. The LED light is a standard USB plug with a On/Off switch. You'll need a USB plug or plug it into your PC usb port to power it. There are holes in the enclosure to fit wires through. The side pocket is handy for any tools. It reduces the noises slightly but it definitely retains any fumes coming off the filament. I am using PLA Plus and it has a odor to it.

We are very impressed with this enclosure. It was extremely easy to setup and fits our Flashforge Adventurer 5M printer very nicely. Unlike a custom fit case, this does add to the footprint of the printer and requires more space than the printer itself, but if you have room it is a great value. The quality of the materials was higher than I expected for the price and I am particularly pleased with the insulative properties of it. There are plenty of access options for cords and such, but I plugged the USB light strip right into our printer and it makes for a convenient and bright workspace. Highly recommended for anyone who is looking for a simple enclosure to keep in warmth and fumes, and keep out dust or pet hair or whatever.

Assembly was very easy. It all snapped together and made sense. The fabric fits over the frame without being too tight that it's a pain, but definitely is tight enough to stay in place. The quality is very good and better than I'd expected to be able to get for this price point. The zipper flap going all the way to the back is awesome for easy access to the printer. I have my printer on slightly higher feet but it still fits properly in the enclosure, though if you have the Extender or taller height you will want the bigger size. The included light bar is a huge addition, I get really good quality videos from my mounted camera and I don't need to light the whole room to do so. I have only printed PLA+ so far but I'm looking forward to printing Nylon, ABS and other materials that want an enclosure. The sound reduction isn't a huge factor but it does a bit for that as well. My printer was already fairly quiet and this made it very nice. The small door on the side will be useful if I decide to do some type of ventilation, especially for lasering. I'm looking forward to getting a lot more use out of this and I may try and figure out a way to print directly from my dryer while still being mostly enclosed. I believe there may be enough space in the enclosure for that.

Easy to put together, seems to stop draughts and retain heat quite well. The opening is big enough to lift an ender 3 in and out with little issue. Could possibly do with not being as deep but my guess it is as such to accommodate different size printers. It's withheld a few months work without issue. I got the enclosure with the LED light and this is surprisingly lights quite bright. Probably helped by the fire retardant coating on the inside of the enclosure. Oh and it is incredibly lightweight.

Per quanto costa è un upgrade alla stampante 3d incredibile, non ho più avuto alcun problema di warping e fallimenti di stampa da quando la uso, ho iniziato anche a stampare ASA e abs con un estrattore in garage e ha dato nuova vita a una stampante che non usavo più.

Easy to setup for my Egeloo printer. Supports appeared strong,cover fit very well. No gaps or rough corners. Cables easy to work with through the cover sides. Reflective interior keeps temp stable. LED light works well. A good purchase!

Lo recomiendo al 100/100 muy buena calidad y se monta muy rápido mi impresora es una bambú lab a1 y entra en el armario perfectamente rine si espacio de sombra lo recuerdo 😊

Ich habe mir dieses Gehäuse für meinen 3D-Drucker geholt und bin absolut begeistert. Hier sind meine wichtigsten Punkte:Geruchsminderung: Das Gehäuse hält unangenehme Gerüche beim Drucken so weit wie möglich ab. Man riecht im Raum kaum noch etwas.Stabile Temperatur: Hält die Wärme perfekt im Innenraum. Ideal für zugempfindliche Materialien wie ABS oder PETG.Integrierte LED-Beleuchtung: Die verbaute LED-Leiste ist super hell. Man kann den Druckfortschritt jederzeit perfekt beobachten.Gute Passform: Die Maße (550 * 650 * 780 mm) bieten reichlich Platz. Mein Drucker passt samt Filamenthalterung problemlos hinein.Einfacher Aufbau: Das Gestänge lässt sich schnell zusammenstecken und die Abdeckung sitzt schön straff.Für den Preis (besonders im Angebot) eine der besten Erweiterungen für jeden, der saubere, geruchsarme und zuverlässige Druckergebnisse möchte. Würde ich sofort wieder kaufen!