Epoxy Putty, 120g 2 Part Fast Repair Epoxy Putty Wood, Metal, Stone, Hard Plastic, Acrylic, Ceramic, Glass, Acrylic Bonding and Repair (Brown)

I needed a product to repair flagstones which had cracked -mixed colors to closely match ( still wish they had a tan available) -this product when mixed is so much easier to use than several other products and did a really good job -not sticky or runny -great product !!!

I used this to fix a fountain and it made a perfect seal. Easy to work with. It’s not as brown as I’d hoped but for this job it didn’t really matter.

I decided to take a chance on this product and it worked well for me. I was prepping an antique wooden wardrobe for painting. At the top of this furniture was a three-piece moulding attached to the top and sides. One of the pieces had a broken-off top edge: about 10 inches long, one-quarter inch wide and ranging from three-eighths inch to one-eighth inch thick. Just guessing, I used about half of each of the parts (epoxy and hardener) to mix together and intended to roll out a "snake" that was slightly larger and about as long as the missing piece of wood. The snake was almost twice as long as needed but better to have too much than too little. (I immediately put the excess in plastic wrap, thinking it might be preserved if it wasn't exposed to air. Nope.) As I was pressing the snake into place, I couldn't tell if it was sticking securely enough. It didn't have a lot of surface area to cling to, but in an hour it was hard and felt like it would be secure. After 24 hours I sculpted with 150-grit sandpaper, both by hand and orbital sander. The adhesion had to be very strong to stand up to the intense vibration of the sander. The cured product was actually much harder than the wooden moulding. In sanding, I had to be careful to avoid too much contact with the wood. The only slight imperfection was the result of my failure to properly shape the "snake" where it met another piece of moulding. NOTES: The leftover piece of snake in plastic wrap was just as hard as the used piece. Using two hands and a little less than full strength, I couldn't break the half-inch-thick snake. When mixing the two parts, there was very little heat and not much of a smell. It wasn't easy to get the very thin plastic wrapper off of the two components.

My fish got run over by the lawnmower. Several big chunks were obliterated. This product gives your fingers a little workout, hubby and I took turns kneeding the two parts together. It moulds easily. I was able to do some restoration and add some details. Not sure about dry time, I left it outside overnight. This is a small amount of product. It was plenty for my project.

Works OK, but expensive for what it is (the pack is really tiny), fairly hard even when mixed—and adhesion on metal is rather minimal.

Sticks good

Advertised and boxed as "Brown", however at best its gray, slight hint of purple even. I added extra brown on a second batch and it still is not even the slightest bit brown, not even tan. Aside from that, it might function properly, meaning it might cure just fine but the color is completely off. See picture attached. Other brand previously used can be seen as "Brown" applied to the table in the picture. VIKEYTIM Brown Epoxy Putty can be seen on either side of the previous product used. Cannot recommend VIKEYTIM if color matching is of a concern for your project.

Lo volveré a pedir cuando lo necesite gracias Amazon!

Satisfaite

Facile à utiliser, bonne plasticité. J'ai pu remodeler mon pommeau de vitesse.

Ich habe eine ca. 50 cm hohe Keramikskulptur damit repariert. Das Produkt wird erst sorgfältig zusammengeknetet und kann dann als plastischer Kleber eingesetzt werden. Es eignet sich sehr gut, wenn kleinere Teile fehlen beim Zusammenkleben um die Fehlstellen dann auszufüllen. Beim Verarbeiten habe ich Einmalhandschuhe getragen - und das war mich absolut die richtige Entscheidung.Die Trockungszeit ist umso länger, je stärker die Schichtdicke ist und dauert unter Umständen mehrere Tage. In der Trocknungszeit fühlt sich das Produkt ziemlich klebrig an.Nach der Trocknungszeit zeigt der Kleber seine volle Wirkung - er hält wirklich wunderbar. Das keramische Material hat sich excellent mit dem 2-Komponentenkleber verbunden.Die bestellte Farbe "braun" wurde nicht geliefert - sondern "schwarz" - die endgültige Farbe war dann ein "grau".

Was going to chuck my favourite water feature out when I broke the rim, but I thought I'd have a go with this first. It dried to the same colour as the feature, is rock solid, and was simple as anything to apply and shape. Now it works as well as it used to, and I am very happy to have saved my Grecian urn.

Fácil de preparar con las manos y el resultado perfecto. Utilizado en el marcó de una puerta para una cerradura de seguridad. Se pega perfecto al metal y al marcó de madera