OREI 1x2 HDMI Extender Splitter 4K by Multiple Over Single Cable CAT6/7 4K@60Hz 4:4:4 HDCP 2.2 with IR Remote EDID Management - Up to 115 Ft - Loop Out - Low Latency - Full Support

We are using this to send digital signage content from a player out to 4 different TV's in a retail setting. According to a Fluke network tester, the furthest run was about 45 meters over Cat 5e cable. This device worked flawlessly. We are using it for 1080p content, no audio, and leveraging the POE functionality of this unit. Our previous sender system died and it required power adapters on all of the receivers. It was a much older OREI model. This new redesigned model is better because there are no power adapters needed on the receivers. The HDBitT transmission medium results in a pristine image, free of sparkles or artifacts that you can see on noisy, long run Cat 5e or lesser quality cable on some other solutions "proprietary" signal over twisted pair tech.So far so good, I recommend this unit for any commercial, retail or even a home setting where you want to send content from one source to up to 4 sources. It is 4k ready, has RS232 serial control as well as Digital and Analog audio extraction from the HDMI source - great features we don't need but you might. It has a convenient HDMI output so we are able to monitor the content from the network closet so we know a good source is being provided to the unit for sending out in the field.

Super easy install! Plug and play

UPDATE2: Received new replacement receiver. This seller came through!UPDATE: After an email exchange with the manufacture the failed unit will be replaced. Thanks for the communication.Purchased the 1x8 HDMI Extender Splitter June of 2022 and installed five of the receiver units when the product arrived.We held off on installing the sixth unit as we were doing a kitchen remodel where the sixth was to be installed. Once the remodel was completed it was installed but this was after the warranty period expired. After 2 months the unit failed. The picture would go black then back to normal and repeat. I swapped it with one of the original installed units and the problem stayed with the unit. So after two months of use the unit is defective.Even though it sat new in the box until it was installed and in use for only 2 months the seller will not replace it.Bottom line the seller will not stand behind their product that was in use for 2 months and went bad.Poor policy. Buyer beware!

Easy to set up. Works like a charm so far. Replaced my POS HDMI 4X4 Matrix with this one. Interestingly the picture is a whole lot better with the Orei. Would definitely recommend it.

I love these but the only downside is the audio lag to the satellite tvs

UPDATE: Device stopped working. Everything looks like it is fine but the remote screens are not displaying picture.This could / would be what I want it to do but running into some issues. This was bought to replace a different brand that works but at the time, did not include IR.1. The receivers cannot be powered over the ethernet cable. You have to plug in all receivers.2. The IR blaster is big. My source sits on a shelf with no room in front to install the IR blaster. I typically can install other IR blasters up against the IR of the source. This has a solid bottom so when I tried to install it like other smaller typical IR blasters, the IR receiver does not see it. My fix was to wrap the cable with a fairly stiff wire and have it stick out from the shelf so that it can get a good line with the IR receiver. I will need to play with this multiple more times to see if I can get it to work without sticking out (sticking out runs into issues with people possibly bumping into it)3. The receiver on one device works as it should. The other one however, when I press a button on the remote, it mutes what is playing until its done executing the command. This is an issue because if I am listening to music while going thru the source (like viewing pictures), then my music will annoying cut out every time I press the button on the remote.4. I get artifacts on the screen at the receiver side. I was able to hit the reset button on the receiver and thought it was good. Then when I went to the other receiver and worked on that. Came back to the first receiver and getting artifacts again. I haven't play with it too much but if I need to press the reset button regularly, I will need to make sure I install it behind the TV where its easy to access.5. The receiver on occasion blacks out. I put this at #5 because it happened a couple times while testing and I wasn't pressing anything. So if this continues, it would be a major issue.

This HDMI over cat6 matrix (210 foot version) has been working great for years. It's the most reliable video distribution method we have on stage.Everything else had occasional video corruption or dropouts. Even expensive dual link SDI gear had problems. This OREI HDMI over cat6 matrix just keeps humming along with the best consistent performance of anything we've used. (While always using edid emulators to keep HDMI resolution changing from causing chaos in the video system).Two thumbs up. Would buy again.

Just arrived today. So far so good. It runs over a 100ft HDMI for input with no problem. Wireless puck input great quality running from my Samsung S24. Seems to be good so far.