Hoolcar for JL Tailgate Table Compatible with Jeep Wrangler JL JLU 2018-2024 Rear Door Foldable Table Cargo Shelf Storage Rack, Support up to 75lb Storage Cargo Luggage Holder Carrier

Installed on a 2010 Jeep Wrangler JKU. Pretty solid construction and good looking. Light weight but sturdy when in use. The missing instructions is not an issue at all. You should be at least average with hand tools to install this table. I didn’t use the one page provided cut outs, put it together using the advertised picture and then line it up where you want it on your tailgate. Helps to have someone hold it while you mark your holes. Drill one at a time and dry fit it as you go. The only thing difficult is the Nutserts you will need to install. I purchase a Nutsert tool on Amazon. If you still need instructions go to Quadratec on line and look up Tailgate tables and open the Rough Country table PDF instructions, this is just like it. I do recommend this table.

It's a good table. I had nothing good to say about Chinese engineering while trying to line up the bottom two mounting bolts. May have said a naughty word or two.

UPDATE..... Doesn't fit my 2012 Jeep Wrangler........... I can't wait to install this on my 2012 Jeep Wrangler. I searched for sometime to find the nicest one and this fits the bill. It is well made, sturdy and I love the design. I'm hoping the install will be easy. I love the two shelves and the cup holders can also be used to put a bottle of wine up through the hole so it doesn't tip over. What a great idea when going off road and you want to open your tail gate for a cold drink, beer, wine, cocktail and/or a snack.

If I hadn't read the previous reviews I would have been stuck. Looks great post install, but ZERO instructions come with this product which is ridiculous. No Youtube install video either... Per the other reviews, this does require drilling four holes into the plastic panel that protects the swing gate. I also used a 7/16 drill bit but had to make the holes a little wider to get the plastic spacers to fit. Product alignment is poor and even after install, one of the sides rubs every open and close based on how it was manufactured. Seems there is very limited or no quality control at the factory. Took me about 30 - 40 minutes to install alone but if your not handy in any way and don't have any tools (drill, 7/16 drill bit, #10 crescent wrench), it's going to be a challenge.

Exactly what I wanted. Fits just fine. Not sure what trouble other people had putting this together. It fits great on my 2021 4xe. I used 1/2 inch bit to drill into the plastic. This allowed a tiny bit of play to make sure I could make it perfectly level. Anyone whocan use a drill, level, wrench, and Allen key should be able to do this. It took about 15 minutes.

No instructions! Watched a YouTube video and my jeep doesn’t match the video. I have a 2014 Saharah and it has drilling into a tailgate panel and my jeep doesn’t have a tailgate panel. I would need to jimmy rig it to be put on my tailgate. Sits in my storage until I figure out how to jimmy rig it. It’s durable, looks great on the floor but it is getting a one star for no instructions and not compatible with my jeep.

It was horrible to install- there weren’t any directions. But if I had to install another one it would only take a few minutes because now I know what to do. You have to take off the back panel. You need a 1/2 inch drill bit for the holes. The holes are already exactly where you need them in the Jeep- but you have to drill holes into the plastic panel to line up with the tray. If I were to do it again I would actually keep the two pieces together when I put them on instead of doing the frame and then the tray. Also the tray goes inside in a concave way. I put it on so that it would open like a shelf with sides- then it wouldn’t shut right so I had to start over. But once it is done it is absolutely worth it!

There are a number of nuts, bolts and washers left over. On my 2015 JK I used the wing nuts and slid them into existing slots on the tailgate. Used two on top and one on bottom. Worked like a charm. Took about 20 minutes to install. I used a Dremel tool to cut around the nuts on the bottom of the plastic and put it back on. Nice product. Lack of instructions was frustrating.

Almost 1 year i am currently using this, all good.