GSCIT Club White Edge Banding, 13/16 inch x 50ft Melamine Edge Banding with Hot Melt Adhesive Pre-glued Edge Banding Flexible Edging Trim for Plywood Cabinet Furniture

As a veneer, the material is plenty thick and substantial. It has somewhat limited ductility. It could probably be wrapped around a 1" dowel (your thumb), but much smaller than that and it will fracture. I think this would very rarely be an issue, but it means you cannot wrap it around a sharp edge of a cabinet. There is no guidance from the manufacturer about the acceptable temperature to set the iron. One reviewer was concerned that the banding could melt if the iron were set too high. However, Melamine is a thermoset, meaning it will not melt. It will decompose at about 650°F. It is also very resistant to ignition, and its ignition temperature is greater than 930°F. A typical electric iron will reach a temperature not greater than 450°F, so you do not need to worry about melting, or igniting the material. No need to put a layer of cloth between the banding and the iron. I don't know the melting point of the adhesive. Standard hot melt glue is dispensed at about 380°F. I also found the banding to be very forgiving, which I really appreciate. This means that if the banding is misplaced, you can simply reheat it, and move it, or remove it.I set the iron on cotton. The adhesive melted quickly, and set quickly enough that the band stayed in place. It was easy to trim with a razor blade. The stuff is really good, and easy to use.

The media could not be loaded. The product came as advertised, It had no colored variances, solid matte black throughout with no breaks. I would recommend a low to medium heat setting on your iron when applying, this product is made of plastic and has the potential to melt. The glue performed fine and stuck well, I had no problem taking off a small spot and reapplying it without damage to either item. Cleaning the excess glue was easy it just wiped off. It seems to perform well it doesn't scratch easy and I expect good durability out of it. Installation was quick and simple Just a simple iron on with low to medium heat and you're good to go! Good value for the price I would buy it again.

This was for a small day fix. I made sure to get the right width for a heavily used kitchen cabinet drawer, the edge of which was having the paint wear from heavy use (it's a pull out garbage/recycling drawer used many times a day). I sanded the remaining paint first (usually not needed but the drawer edge had some uneven wear that would have probably made this edge banding less effective), then got a strip ready and just ironed it on (the glue side melts onto the surface when you apply a hot iron-- i.e., you hold the glue side down to the edge you want to stick it to, then iron the regular side so the glue melts and sticks. Making sure the placement is good is important, but I think if you messed up you could probably scrape or otherwise remove and try again. Then snipping off any extra at the ends, very carefully. Looks great, is easier to clean, and have not had problems though it had been on for at least a month. The one thing I would say is that there really aren't instructions, so I had to guess at iron temperature for instance. Otherwise great.

I didn’t even know this was a thing until I randomly came across it. The edging on our shelves fell apart years ago, and at first we used tape and then just paint only, but the unfinished edge is so obvious and ugly. This stuff is so easy! Just make sure you get the correct measurement. You can cut it if it’s not right, but I think its easier to get the right size at the start. Then just hold it down and use a clothing iron to press it down. It adheres right away, it’s so cool! No nails or tools required. Our shelves look brand new now.

This product is easy to use. Sticks well with a hot iron, easy to trim and not too thick as to have visible edges. I found that using fine sandpaper to perfect the edges made it blend in well with the adjacent sides of my work piece and difficult to tell that any edging had been used. Now on my 3rd roll of this product for a large built-in shelving project, and no complaints.

I made some pullout kitchen drawers, and needed this for finish the edges. This edging works great -it's color matched, and applies very easily.I try to be precise in measuring, cut once, and minimize waste. But of course it's better to cut these a little long than a little short. Then if you've got a little overhang, just take a sharp pair of scissors to trim that off.Once heated with the iron, it sticks pretty fast, but if you mis-appply it, you can just put the iron on again to soften the glue and reposition.I bought the width trimmer on Amazon, as well. That's kinda tricky, and takes some practice. It's almost worth putting the edging on a scrap piece so you can see how it works so you don't mess up your actual finished piece. You gotta squeeze the trimmer, but not too hard or it bites too much and tears the edging.

Got this trimmer today just in time to do some trimming but i am using 3/4 maple plywood and the tool does not want close that small but the description of this trimmer claims to be able but it does not .As a single sided trimmer works really well, what took me hours and lot of swearing, now it took minutes and is super easy.the seller says to E-mail them but what is your e mail i could not find it anywhere.

Exactly what you would expect. Went on easy, easy to trim. Looks great for a finished look.

Tres robuste et à bon Prix, pratique et élégant

This product works great. Cut the strip, put it on and set your iron to wool and iron dry on top of the tape and it glues right on.

Love it. You need heat gun to melt the adhesive while applying to get it stick. The results are amazing. I need that while doing some fillers on cut panel of Ikea. Will buy more if I run out.

Parfait exactement ce que je voulait et le prix est abordable pour la quantité

250 feet for the same price as the big stores for 25 feet