KSP 1.25" Wheel Spacers for Tacoma 6 Lug Wheel,4pcs 6x5.5 Hubcentric Spacer fit for 4runner Tundra Fj Cruiser Sequoia,32mm Forged Spacer with 12x1.5 Stud 106mm Center Bore,6x139.7 Aluminum Tire Spacer

Perfect fit, great quality. Stock wheels and tires shown still give it a simple mean stance. Will update if anything happens

**For anyone owning a tacoma, you must get the size with a lip (hubcentric) so that your wheel can correctly mount. Otherwise you will get vibrations.Great product. No problems so far. Seems very strong and I haven’t been worried that my wheel is going to fall off. Just make sure you constantly torque it for the first 1000 miles as the lugs are brand new and thus will stretch as they break in.

Direct fit with no gap for a 2017 Tacoma . Very easy to install and comes with lock tight . My only recommendation is to use blue lock tight instead of red if needed to take off the wheel spacers down the road for any maintenance . Overall great product and comes with all the parts you need . This is with .285/75/16 tires and a 3 inch rough country lift

They are made well, and they didn’t fit my factory wheels on my 2019 Tacoma I didn’t know I needed to have a hubcentric type spacer,, do your research and buy the correct spacers. So you don’t have to take them back off and return them.also one stud did break off at 50 lbs tork:(

15 GX460 good quality, 1.5" brings wheels out just enough, minor rub at full turn backing up, just remove front inner mud flap attached to front bumper.

Still to early to give a review but so far they are great, specially when they send you locktite.

Wheel Spacers for Toyota, KSP Forged 4Pcs 1.5" 6x5.5 to 6x5.5 Thread Pitch 12x1.5 Hub Bore 106mm 6 Lug 38mm Hub Centric Wheel Adapters for 4-Runner Tacoma Tundra FJ Cruiser Sequoia, 2 Years WarrantyUp front: The spacers, as shipped, won't work on a gen 2 Tacoma (2005-2015). I'd venture to guess gen 1s and 3s would probably have the same issue as well. The hub's lug bolts don't even get close to protrusion (barely make it halfway through the nut) with the included nuts. I'm trying to find a workaround (maybe extended thread nuts or longer studs) and will update this review with the seller's response and again if I'm able to successfully install these.Ordered these spacers for a 2007 Toyota Tacoma (2wd PreRunner with 6-lug rims). The item description indicates that these spacers will fit and, for the most part, they do. The hub bore is perfect (no play on the hub but still slip on with ease), lug bolts center up, and the bolts on the spacer are the same size as the hub (M12x1.5) so the factory lug nuts will screw on to the spacers.The problem: There is absolutely no thread protrusion from the hub's lug bolt with the spacer kit's lug nut. Not even close (see photo). I ensured the spacer was seated flush against the hub and the lugs were centered in the spacer's holes (so the lug bolts would fully seat in the tapered holes on the spacer) but after tightening them as much as possible (with the hub still spinning freely, so maybe torqued to 25-30 ft-lb) the end of the bolt was roughly halfway through the lug nut. I didn't torque them all the way to 80 ft-lb but there was no way I was going to get even 1 more full rotation, which was certainly still not enough to get adequate thread protrusion.The instructions in the package say that lugs to attach the spacer to the hub are not included and call for open-end conical seat lug nuts of the appropriate diameter/pitch to match the hub's stud. The package does include M12x1.5 open-end conical seat lugs (which are, in fact, exactly what the instructions say are needed to mount the spacer to my vehicle i.e. correct size). Also, these nuts would not work with the factory wheels as they do not use a conical seat. Furthermore, the included instructions conflict with the mounting diagram in the item's listing (see attached). One says that the included lug nuts are for mounting the spacer to the hub, the other says they are for mounting the wheel to the spacer.Since the included lugs matched what the instructions say are needed to mount the spacer, I used them to attach the spacer to the hub. Obviously they won't work and now I'm a little concerned about finding one that will. These nuts are already shorter than anything else I've found. Their slightly less than .80" tall and most of the replacements I've found are just over .8" at best. Seems like extended lug bolts for the hub are the only confidence inspiring solution given the circumstances. Hopefully KSP responds with a solution soon.Update: Ordered some extended thread nuts (http://amzn.com/B01N03AQIU) for $32 to hopefully solve the problem. I got roughly 6 full rotations out of the included lug nuts. The new nuts have a 0.3" (7.6mm) shank that extends below the taper and into the holes for the wheel studs. The extension should add enough threads to ensure at least 9+ full rotations which would achieve the recommended 12.5mm of thread engagement on the wheel stud even though the stud doesn't protrude through the nut. I measured the space between the bottom of the included acorn style nut to the back of the spacer (roughly .4") and the diameter of the bottom of the hole (roughly .65") to ensure the new nuts would fit in the spacer and not bottom out on the hub before being fully tightened, so these should work. It would have been nice to know I was going to have to spend and extra $32 to make these spacers work. The ad is a bit deceiving.

I needed to run spacers on my Tacoma to clear my tires from the upper control arms, started with 1.5” but settled on 1.25” for because of mud flap rubbing issues. The spacers are clearly made from billit (meaning machines from 1 solid piece of aluminum) the clearance between the bore extrusion and bore on the truck is almost perfect, almost no play at all. The studs seem to be of decent quality, not oem by any means but it’s a small truck with 6 lugs, I don’t have any fear that they’ll break. I measured each spacer with a micrometer and they are all within .005” of an inch, which is acceptable. KSP makes some pretty nice products at an affordable price. I’ll continue buying their products down the road