SPARIN 2-Pack Screen Protector Compatible with Microsoft Surface Go 3/Surface Go 4/Surface Go 2/Surface Go, Tempered Glass, High Responsive, Scratch Resistant

Don't miss the part in the description that says it's a MATTE, ANTIGLARE, WRITES LIKE PAPER screen protector. I am giving this screen protector 5 stars because it is the perfect protector for someone that wants a MATTE easy to install screen protector. I missed the MATTE part which is completely my fault. I purposely purchased the surface with an OLED display because i wanted the crisp display. This screen protector is very matte for antiglare, very gritty like an 800grit sandpaper which gives it that paper like feel. It makes the display grainy which is exactly what it's supposed to do. I'm not even sending it back since ordering a MATTE one was completely my fault and the seller shouldn't have to eat my negligence. I wish Sparin would make this same installation kit with a clear smooth protector, I would have purchased that one.

These worked well and gave that tactile feel without overdoing it. The applicator made it easy as long as you read all the instructions before you start!

Protector itself has a great texture and the glue is holding to the screen really well. Installation is pretty easy with the tool that is also the product packaging. I did have to swap my original shipment out due to debris under the protective coating, but amazon makes that easy. Would buy again for sure.

No matter how many screen protectors I've installed it is always the same, the particles that mysteriously appear After you have cleaned the screen and set the protector in place. In the case of this protector I ran into a new issue. When I used the included wet wipes my horror began. The wet wipes provided left streaks all over the screen that took me a half hour to remove. Once I cleaned that mess off I attempted to set the protector in place, after using the lint lifter, which I may add is a plus and necessary. I set the protector in place, and of course, little particle bubbles all over. I quickly lifted the protector off and using the lint lifter pad went over the screen Again, and when I looked at the sticky side of the protector it looked like someone had just sprinkled it with lint everywhere, now where did that come from. But, I used the lint lifter pad on the sticky side of the protector and it removed the lint, or dust, or whatever it was. Had to do this three times before I got a perfect install, that was fun. Just have to be naked in a clean room I guess. But it looks and functions perfectly, touch function is perfect. This is a nice product, just don't be in a hurry, be meticulous, and meditate before during and after, hey, it may help.

I don't write reviews normally. The biggest problem with screen protectors is getting it situated over the screen, pulling off the films and getting the inevitable bubbles out. We finally have a consumer product with a well engineered install process that makes the consumer look like a pro. This has a tray to hold your device and a protector that locks to the tray over your device. This takes the skill out of positioning the glass. Close the box and pull from the bottom and the glass is installed. Their squeegee is better than the rest. All the bubbles easily came out. You will be happy with the install.

Easy to install highly recommend

Fits my surface 12in and the matte texture is perfect so I can take notes at school

This screen went on fast and was actually easier than the one I put on my cell phone which cost much more. The tabs are key. First, watch the youtube video. It shows putting 2 tabs on the short side, I used 3 tabs on the long side. The protector is very very slippery and I didn't have a helper to hold it in place while I attached the hinge tabs to the screen. So what I did (BEFORE removing film) was position it by using a small piece of scotch tape in the middle of each short end, applying the tape to the protector top first. You can then ease it in in place and make fine adjustments without worrying about messing up the provided hinge tabs. Press these scotch tape pieces to the edge of the Surface Go and double check alignment. Adjust if necessary until perfect. THEN put the 3 hinges on the long side. When these hinges are folded over and attached to the protector you can take off the scotch tape pieces and proceed to cleaning. Important: make sure there is no slack in the hinge when folding over onto the protector I have hot air heat in my house which blows around a lot of dust. I turned the thermostat down (or up if you have A/C) so the system wouldn't trigger and start blowing dust around in the middle of my installation. I also wiped down the surface I was working on, and washed and dried hands with a microfiber dish cloth. I used wet swab, then dry swab then tacky strip. I removed the film steadily and quickly trying not to stir up any air current. (don't let the sticky side touch anything after the film is off!) I closed the hinge and it immediately started adhering from the hing side across the screen until it was solidly on. Not one piece of dust or bubble, and perfect alignment! Love it!

Good thanks

Just like many of the other reviews said, I found it perfect, too. I had a bit of trouble getting out one bubble, but I think that's because my original screen already had a scratch in that spot. Other than that, the instruction video is very accessible on YouTube, and the accessories provided work perfectly. Glad to have better protection now, for my Surface Go screen

Comprato per il Microsoft Surface Go2 ed è perfetto, non arriva al bordo è meno di 1mm più piccolo dal bordo ma nessun problema anzi. L'applicazione è facile e veloce, nessuna bolla, appena lo applicate aderisce subito. Nella confezione trovate anche 2 salviettine con l'alcool perché sono due i vetri che vi arrivano, un panno per pulire, e le istruzioni, tutto ben custodito in una custodia rigida per conservare il secondo vetro, veramente ben fatto.

La mica es como todas, nada extra. Pero envían muchas cosas innecesarias que solo generan desperdicio. Todo viene en plástico, a este punto ya deberían saber que todos tenemos pañuelos, alcohol para limpiar pantallas, pegatinas para remover polvo, etc. Lo único entendible es el empaque en donde vienen las micas, pero lo demás es BASURA.

Tiene hueco para los sensores de cámara. Perfecto, sin marcas ni burbujas. Un 10