3M オートミックス パネルボンド#8115

ポルシェの、カーボンルーフ加工に使用。20分程度で硬化し始めます。その間に接着物の両方にヘラで塗布均一化を行い。接着します。特にFRPやカーボンは、塗布後 硬化が早いので、早く接着が必要。最初は、ゴムの様ですが、硬化後は、カチカチになります。

スチール、アルミ、ファイバーが接着出来てとても素晴らしい接着剤です。 基本的な下処理をきちっとする事が大切です。 価格が高い高いのが難点です。 自分が思っているよりたくさんの量が必要な時が多々あります。

車両の補修、修理主に錆びに対する補修等に大変便利使用させてもらっています。

ノズルは最初から二本付属しており、追加購入する必要無い。 ノズル単品は値段が高すぎるので、付属するのはありがたい。 説明書を良く読んで使用すれば固まらない事は無いが、気温が低いと固まり難く気温が高いと垂れやすい。 溶接出来ないほどの薄い鉄板はパネルボンドで接着する方が安全だ。

品質にはもんだいなし、製品が、他の物と大きな違いは無いのに、高額過ぎ

Good stuff

This stuff is superb! High grip adhesive. Holds where it is placed so make sure to put it EXACTLY where you need it since you’re not going to get it off again! Adheres to literally everything I’ve tried it on.

Très bon produit et efficace

Easy to use. Great bond.

I used 3M 08115 for the first time on my 1954 Chevy Pickup that needed some small patches on its holey roof and firewall. I chose this product after many hours of research and debating vs welding, braising, fiberglass, and other products. the le reason why I chose this is because welding large surfaces such as a roof can warp the roof if not done properly and even then there is no guarantee. Another reason is that welding melts both metals down and can potentially inbed impurities and rust into the weld only to pop up later. With this epoxy you eliminate the potentially for any of this to occur. This is probably some of the reasons why most car manufacturers are using this product to secure their panels on their cars in lieu of welding. Also, because it seam seals all in one step. From all the forums posts and reviews that I read I was unable to find anyone that had actually used this product that wasn't completely satisfied with it's performance. I borrowed a really nice gun (it requires a double tube epoxy gun btw) from a friend and went to town. It applies like hot peanut butter, gives you plenty of working time, smooths out flat, and it cures hard as steel. I love it. I have since used it on other projects and it has performed great. Some tips: It says on the product material that you can reuse it by leaving the tip on there, let it dry and leaving it on till you need it again at which time you just unscrew it and put a new one on. I read this after I have cleaned the outlet very well and put the top back on. This can be a little tedious. Using the used tip seems a lot easier to do. Another tip is that I was working with small 2"x 2" patches for my non structural hole repair. I found that using small yet strong magnets to keep the patches in place as they dried worked awesomely. For the intended application, it is the best there is. Try it and you'll agree. Update....... I have used this product a lot since this posting and continue to be in awe of its strength and ease of use. I can see most welding falling into antiquity when everyone finally brakes from what they are used to and tries this stuff. BTW for shorter claiming times, apply heat from a heat gun. It sets up in about three minutes. Another benefit to this product is that you can bond unlike metals such as steel and aluminum and since there is a layer of epoxy in between them you don't have to worry about them reacting with each other causing galvanic corrosion. sorry for the long-winded review but I hope you find this helpful.