1460Pcs 1/4W 73 Values 1% Precision Metal Film Electronic Resistor Assortment Kit Set 1ohm-1Mohm for Arduino

Great value and variety. I also love that they came with a band legend sticker. That will be useful to stick on the lid of the sorting tray they will go into. On the down side; The pouches were not in order, a few of them were mislabeled (but the stamp on the ribbon was correct), and some of them were labeled differently even within the same value range. (See pictures)BUT, those few complaints are fairly trivial when you start to test and use these items; testing a random smattering of the resistors shows that they do indeed fall nicely within the 1% range, which is really all that matters here. Random tests pictured.

A well-organized, complete selection within its range. Note that the largest value is 1Megohm - I need a few values between 1M and 10M and had to cover them separately.The resistor leads are thin but that is actually a convenience - two leads can fit in a single standard perfboard hole if needed. And they have held up just fine to bending, resoldering, etc so they are not flimsy at all.

Bought resistors for stock need to be used as needed. Color code could be better. Best to check each device with a meter to know what it's value is. Other than that, these devices will do what they are designed to do. A superior PLUS for metal film resistors, you can get them hot enough to burn the surface paint off, but the element holds it's resistance value. That is not possible with carbon film, or carbon composition resistors.

Lots of resistors with many values. The few test circuits I've built with them have worked as intended, so they seem to be accurate. I actually did have to test the resistance with a meter after my 10 year old disassembled my breadboard and made a pile of everything. I would have tried reading the codes, but they look like the bands were painted by a dog. I mean, the colors are not easy to differentiate, some are fairly thick bands while others are very narrow stripes, some are partially missing. It's hard to tell which end to read from. Bottom line, they're a pretty cheap price but they seem to work well (so far). As long as you pull them out of the baggies or use a meter to check them, you should be okay. Recommend.

Who can resist a box full of resistors? I use these for general projects. Comes in a small cardboard box, and each set of resistors is in a tiny ziploc bag. So it's a box full of 73 little bags. Each bag is marked with the value, which is great since I can't read the color bands (an EE with color deficiency). I spot checked a few, they were all within published specs. Great value.

All values measured well within tolerance. Each value packed separately and well marked. The leads were thinner than what I had hope, but that seems to be pretty standard now compared to years ago. Still not a problem if your using a quality breadboard.

Great selection of low wattage resisters. Accuracy is very close to markings. a great low cost order for your building hobby.

Falsely advertised as 0.5 mm leads. They fall right out of the breadboard.

Easy to read, organized and a great addition to my R/C hobby.

Die Widerstände sind getrennt, nach Werten sortiert und in kleinen beschrifteten Beuteln verpackt.Eine aufklebbare Farbcodetabelle lag auch bei.

Die Anschlussdrähte, mit 0,32 mm bis 0,36 mm, als "Thick Legs" zu bezeichnen, ist etwas weit her geholt. Marken-Widerstände haben da 0,6 mm. Die Toleranz mit 1% halten leider nicht alle Widerstände des Sortiments ein. Im schlechtesten Fall habe ich Abweichungen von 5% gemessen. Auch den Temperatur-Koeffizient würde ich nicht als "Low Temp Coefficient" bezeichnen, da ich eine Abweichung von mehr als 300ppm pro Kelvin gemessen habe. "Metallfilm"-Widerstände sollten da ehr bei 50ppm liegen.Zum Basteln auf einem Steckbrett oder Lochrasterplatine reichen sie aber aus.

Parfait pour mes montages audio. Plus besoin de chercher les valeurs. Ménage un temps incroyable.

The leads are quite thin, so depending upon the state of your breadboard, the leads can be too loose or too flimsy to push in.If you are soldering, then they will work well.