Epoxy Resin 2.25 kg Fibreglass Kit | Professional Quality Clear & Odourless Lamination and Resin with Hardener and Gloves, incl. English Instructions

Excellent product, mixes easy and is super clear and hard. This is the first time I've used anything other than 1:1 ratio. The resin is very thin/runny compared to others that I've tried so not as good for some techniques where you need the resin to be thicker but great for the right projects. Will definitely order again as it's great value for money and lovely finish.

A very good clear easy to use resin with a fast cure time measured by weight not volume so requires a digital scale to measure but they can be picked up cheaply from Amazon, dries really hard and super clear, easy to work with and produces excellent results this is my second purchase of this resin and it will be the one I continue to buy

The media could not be loaded. Being recently new to the resin craft I tried a fait few different products then I found this one....what a game changer! Barely any odour to it & sooooo easy to use. Mixes really well & leaves a great clear finish. Also dries great too. I'm about to order my 2nd lot as soon as stocks come in. I have posted about this on my Instagram so others don't have to waste time or money on inferior products. If any criticism it would be I wish it came in a bigger size :)

I have only done a few small projects so far with this resin however, it definitely does have a yellowish tinge if you either try to pour more than a 1.5cm depth in one go or use a lighter a little too enthusiastically. The thinner items I have done are clear with no yellow cast on them. I had no major issues with bubbles even without the lighter and in fact found less bubbles in this than my more expensive resin.The bottles I found difficult to pour from for small projects so am adding some pumps to make this easier and less wasteful.All in all a great value resin with few issues as long as you follow the mixing and pouring guidelines. I would say be prepared to take more time for larger projects and allow each layer to fully cure before pouring the next.Fyi I mixed mine by weight not volume as that's what the guidelines said and it worked great for me. To get around the issue of not being able to use the lighter I warm the resin and hardner in a crock pot I use only for resin for around 45 mins starting in cold water. Once fully mixed I also returned the mixed resin to the hot water (carefully so as to no introduce any moisture) for a few more minutes. Crystal clear results but much lower pot life with this method. Needs to be somewhere warm to cure as well, I left the remnants in a colder room and while it did eventually cure it took three times as long.Hope this all helps as this is great resin to keep costs down especially for beginners.

Used for carbon fibre cloth and does the job so well

I am very disappointed, I've mainly bought this product for sealing stones and other small similar projects, but it's been a complete disaster.First, I've noticed that the Resin bottle part I've received was a yellowish colour...I've followed the instructions given, but the result was a very uneven seal, runny in some parts, wavy in others. A real pain to fix afterwards, and some of my pieces have been ruined !Perhaps as casting it is not that bad, but like I said above, the resin was out of date.I wasted money, I will not buy again. I will go back to cheaper resins which are surely doing a much better job.Check the batch date before opening it !

The amount of acrylic diy gifts I can make with this is insane hardly any smell and dries quickly

Easy to mix, just make sure to stir for at least 5 mins for best results.Along as you have good temperature conditions you get a glass like finish.I made a couple of mistakes, I used sticks 4 all grab adhesive to stick some of my bottle tops and in the area I used that I had loads of bubbles which a heat gun made it worse, I am presuming some kind of reaction. Area where I used cheap grab adhesive was fine.Also make sure you can keep it in stable temperature, I was doing it in an outside project, first 2 pours where Crystal clear, last pour had a frost on the night of the pour and resulted in a wrinkle effect on top. My own fault for rushing and resulted in lots of sanding and polishing to get it back to a good finish.