Revell 39604 Contacta Professional Glue 25g

First thing people should know. Is you may have to heat the metal needle to get glue to flow. On the first time anyway. It is a perfect glue for fine tiny metal parts and accurate placement. It does dry quickly and holds hard.Definitely recommended for super fine model detailed. And for general purpose plastic model building it works fine for that too.I’m heating the needle. All you need is a lighter and heat the needle for about three or four seconds and glue will flow.

Easy to use, makes a great bond and lasts awhile. I recommend it to everyone who asks what glue to use.

The bottle has a small diameter metal tube for precision application. Light squeeze for a tiny drop. Just right for assembling models. After use hold bottle with tube pointing up and squeeze top to bottom to pull glue in to clear the tube. Store with tube point up like the picture. Don't leave glue in tube. A fine wire to clear the tube would have been nice. This is the same formula plastic modeling glue that has been around for decades. This particular formula is thin for precise applications, not thick like the glue in tubes. This type of glue is not fast setting and parts need to be held together for a few minutes. It is not CA and will not "fog". It is not meant for all plastics.

Great product that works for glowing plastic models please be aware that you only need to use a little or you will make a mess. This has been used to put together at least 27 models and there a lot of it left the product is great and non of the models have come apart even when they fell

I thought the extended applicator would make this product easy to use and apply on the model only to find out that you can’t truly control the amount of cement as it just sort of runs out of the end of the applicator making it difficult to remove or sand down or paint over. I tried to return this Amazon suggested I take it up with the manufacturer so don’t bother wasting your money on this garbage.Thanks for standing by the product you sell Amazon.Junk!

The glue is absolutely fantastic at holding plastic bits together firmly with hardly any used per application. I believe it also fuses the plastics. Easy 5/5 however, my experience with the shipping & bottle detract this quite a bit. First off when the package arrived the glue had leaked all throughout the package (thankfully the only item in the box) with a thick coating of glue around the entire bottle I had to chip & peel off. It seemed fine until I used it the first time when I realized the glue leaks from where the plastic connects to the metal tube. Eventually the plastic tip broke off & I ended up sealing the remaining glue into a jar. It is very thin so you can still apply it with a brush. The only reason I purchased this listing was because it was the cheapest offered with free prime shipping & I needed it ASAP. I ended up buying a new cheaper bottle from a different Amazon listing & haven't had any issues so far

Envase muy practico

i read the mixed reviews, but was willing to give this a chance. it took some doing, but im happy with what ive got. if you want to take the chance, read this first:bad news: there's no seal on the glue container. so you're practically guaranteed to have a clogged applicator tube. thats assuming it even reaches you without having snapped off and spilled into the bag it ships in. if it does, you CAN'T do a return because its considered a hazardous item and amazon wont ship it back. its possible you can still get a refund, but im not entirely sure on the policy for that.the best advice ive found is to burn the metal tube. hold a match or flamestarter under the tip and you'll notice the glue should catch light and burn out of the tip (because the glue is highly flammable. SO REMOVE THE METAL APPLICATOR TUBE FROM THE GLUE CONTAINER BEFORE DOING THIS). if you can clamp the tube, try burning/heating the entire length of it. it took a while of doing, but i finally managed to unclog the tube mine came with (it was REALLY clogged. not just the tip. by the time it was cleared out, the entire tube was miscolored from the heat)now for the good news: if you dont have issues with the container/applicator, the glue itself is good. i'm using it to assemble plastic miniatures and even a slight amount greats a strong hold. for those that dont know, this isnt like super glue. super glue just creates a hardened clump of glue that sticks to both surfaces. this stuff actually partially dissolves the plastic of both pieces and fuses them together. so you're going to get stronger bonds. this can be better for some applications than others. and if you're hoping to be able to 'snap' pieces out later and reposition/replace them, you're not going to be able to do that with this glue.