HoneywellTouch Screen Single Stage Thermostat, Arctic White, Unit

Installed as a replacement thermostat for a conventional AC and forced-air gas heat system that had a thermostat mounted in the "wrong" room. This unit, combined with two of the C7189R1004 Wireless Indoor Sensors, let me move the temperature measurement point away from the thermostat to the places in our multi-room zone where two of us work all day. You can optionally enable or disable the thermometer inside the thermostat itself so that you're only reliant on (an average of) the remote wireless sensors. This is exactly the change we wanted and the result is a very comfortable, rock-solid steady temperature in our part of the zone all day long. Plus it gives us a lot of features we didn't have before, such as treating our large home office like a commercial building. So it will run a fan continuously during our "open hours" while the AC cycles on no more than 3 times per hour. We can start an air purge an hour before work begins. All of this is easily configurable in the Installer Options menu. None of this was really clear to me when reading the description with all the "if / but" caveats and compatibility warnings.I was able to install this thermostat pretty easily by doing a wire color map-over from the 5 wires going to my old tstat (red goes to R, white to W, etc with the only tricky one being blue/common goes to C). The whole thing works like a charm. At first, it was misbehaving and the fan would not turn on. I uninstalled and reinstalled the thermostat and then it worked perfectly. Apparently, I had a loose wire the first time, an easy mistake to make with the wire-block terminal it employs. Be careful that you really do have solid continuity in the connections, otherwise, you could end up with weird behavior like I saw at first.Speaking of which, my system shows 24 volts AC between the red wire and any other. Test yours with a voltmeter if you want to know that you'll have the same great plug-and-play experience that I had. If you have a heat pump or other system, this thing might even be smart enough to make that plug and play but I can't speak to that.By the way, the instructions are garbage and the phone support unreachable (seriously I got a "we're busy, call back in the future" recording). If this didn't end up working for me after the reinstall, I would have sought help from an hvac pro online or in my town. Or I might just send this unit back and buy one with understandable instructions. For example, the installation guide says that you must have the Redlink unit to work with the Wireless something. So did that apply to me and the sensors that I bought? No. It was talking about some other features that I didn't want or buy. Like we're supposed to know all this Honeywell terminology as an end user. Just plug it in, see if it works, and stuff the return to the seller if it doesn't. Maybe they'll get the message and make setup less confusing for an end user.

I had the "old school" thermostat but when I was deciding to change the "working" circa 2000s mid-efficiency furnace I thought I would try this first and so far it appears to have solved some of the issues... Have not had it long enough to see if my gas usage decreases...

I bought this thermostat to solve poor control of the temperature in the master bedroom suite. The old thermostat was located in the hallway outside the master bedroom door and with that door closed the thermostat was controlling the temperature of the hallway but not the bedroom. Even with the door open, the thermostat was not sensing the temperature of the bedroom very well and the bedroom and bathroom were always too cold or too hot even with a lot of fiddling with the temperature setting on the thermostat in the hallway.I considered relocating the thermostat to the bedroom but this would have been expensive and there was another room, the bathroom, behind a door that would still not have proper temperature control. I decided to install this thermostat which has Honeywell's RedLINK wireless capability built in allowing it to communicate with a portable temperature sensing control that can be moved to the bedroom or bathroom when ever needed.Installing it was quite easy, at least for my conventional system with five wires connecting to the thermostat. I just photographed the old terminal block as connected and connected the VisionPRO thermostat the same way after mounting it where the old thermostat had been.I followed the setup instructions provided and did not run into any difficulties. After verifying that the system was working, I put batteries in the Honeywell Portable Comfort Control (which I purchased separately) and added it to the RedLINK network following the provided instructions. It took just a minute or two to do this.I now have a portable thermostat that can be placed in the bedroom or the bathroom as needed and the temperature is controlled perfectly. All of the programming features of the VisionPRO thermostat are available and they use the portable temperature sensor rather than the sensor in the hallway mounted thermostat. Problem Solved!By the way, RedLINK is not Wi-Fi in case you were wondering. An accessory gateway is available that supports connecting the thermostat to your Wi-Fi network if desired.

This thermostat is a great product and is very easy to use. Here is something to know, this thermostat may say it is a heat pump thermostat, but it doesn't have a W2 wiring zone because it is made to only control a 1 heat 1 cool system. Still a great product and no down sides.