ABN 3-Jaw Gear Puller Set – 3in, 4in, and 6in Removal Tool Kit for Slide Gears, Pulley, and Flywheel

Great set for the price! I used the middle size to change the front hub assembly’s on my 08 Altima last weekend. Worked great!!!Update: a week later I’m changing cv shafts on both sides & this Puller set worked like a champ again.The tools are well made of hefty material. I have used the outside griping part (grapple I believe) and it’s stout! I have not just used the outward facing top hooks yet. As I have not needed that function yet. All in all I say it’s a great buy & a must-have for anyone who works on your own vehicle.

The fact that you get 3 different sized pullers is awesome. These seem like they are built well, got me through my job, and now have a home in my tool box.

Used this to pull lower housing from winding assy on "Jet" brand model 700LL airator motor. Worked fine.As with any 3 (or 2) jaw puller, it works best with 2 people (men, women, or children); One holds the puller arms in place while the other tightens the main screw until the screw is snug & a wrench can be used.External finish of puller arms appears to be 'as forged', not polished. This is a cosmetic 'defect' and does not take away from the functionality of the puller.Main complaint is the nuts/bolts used to connect the arms to the 3-lobe central 'spider' are not equipped with lock nuts and are easy to come loose. I plan to replace these with elastic-style lock nuts. Wonder it they are English or metric--I guess I will find out.Over-all: pleased with what I got (all 3 sizes) for what I paid.Carl, Westerville OH

I bought this set to remove a jaw coupler frozen to the drive shaft of an engine for a log splitter. After 10 years of use and some rust build up on the drive shaft the coupler would not budge a mm even after heating the piece and striking it from the backside with a hammer. I bought the set not knowing what size was going to be the correct size (turned out to be the 4") to do the job. It pulled the stuck part with little effort and no damage to either the tool or the drive shaft. This is a heavy duty, inexpensive tool which should satisfy the needs of most DIY'ers. I recommend the purchase of these gear pullers.

These gear pullers worked great. I got 3 different size pulleys off within 30 minutes of the package being delivered. I’m very happy with them.

I get it, they are cheap so they are going to be built cheap. But even so I think they should be designed a bit better. All of the times I have went to use these I have ended up grabbing a posi lock or higher end puller instead. The spacing between the threaded plate, and the puller arms is not the same. This makes the puller arms very loose between the two metal brackets that hold it to the body and allows the arms slide oblong on the bearing or gear instead of staying spread evenly, then the puller will just fall off. I was able to fix this issue by installing washers between the puller arms and the pivot brackets to take up some slop. Another issue is that the hardware is very low grade, lock nuts should have been used. The first time I went to use one all 3 pullers had completely fallen apart just from bouncing around in my service truck tool box. Bottom line is I don’t think these are a very good value. It would be a different story if the thickness of the puller arms mounting holes was the same as the puller plate so there was no slop between the arms, and better hardware with lock nuts.

This is a very useful set of three jaw pullers. Each puller has two jaw positions to allow the puller screw to be positioned as close as possible to the center shaft that it pulls against. The jaws may be set to grasp on the outside of a rim or between spokes against the inside of the rim. The price is very low for this set of pullers. A user should know that the short bolts that hold the jaws need to be tightened only finger tight and a couple of washers, a short piece of pipe or a properly sized socket should be placed on the shaft against which the puller screw is to be placed and tightened. Once pressure is exerted, a light hammer blow on the head of the screw should be dealt to start the pulled hub, gear, pulley, etc. on its journey off the shaft.

I needed a set of gear pullers to remove a stubborn A/C compressor clutch on my vehicle, and this Set of 3 ABN 3-Jaw Gear Puller Set did the job with ease! The pullers are very well-constructed of forged hardened steel, and the jaws are reversible, so they can remove either inside or outside pulleys. Of special interest to me was that each of the three tools were adjustable for either short-reach or long-reach applications, making these gear pullers much more versatile than other brands. The jaws on these gear pullers are also slimmer, which allows access much tighter spaces than other brands. I am extremely satisfied with this Set of 3 ABN 3-Jaw Gear Puller Set, and I highly recommend these!