معلومات عنا
دعم العملاء
احصل على التطبيق
قم بتوجيه الكاميرا لتنزيل التطبيق
حقوق الطبع والنشر © 2024 Desertcart Holdings Limited
🚰 Upgrade Your Plumbing Game!
The Lead-Free 2 PCS Brass Angle Stop Add-A-Tee Valve is a versatile and durable plumbing solution designed for modern appliances. With a lead-free construction that meets strict safety standards, this valve is perfect for icemakers, dishwashers, and under-the-counter water filters. Its corrosion-resistant design ensures longevity, making it a smart choice for any home improvement project.
| Size | 3/8 x 1/4 Add-A-Tee |
| Material | Brass |
| Brand | LitOrange |
| Connector Type | Tee |
| Thread Size | 3/8 inch, 1/4 inch |
| Exterior Finish | Brass |
| Thread Type | NPT |
| Number of Pieces | 2 |
| Manufacturer | Litorange |
| Item Weight | 2.89 ounces |
| Package Dimensions | 5.71 x 4.09 x 0.75 inches |
| Is Discontinued By Manufacturer | No |
| Measurement System | inch |
| Batteries Included? | No |
| Batteries Required? | No |
W**B
As advertised and well packaged
Quality = good, rubber washer = made good seal . my advice is don't over tighten the connection - not necessary, just follow the installation instructions. And remember to use the plastic ferules plus sleeves on PEX - discard the brass ones
R**A
Works
Fits nice
K**B
Easy to use and saved me a lot of money
Lowes and Home Depot refused to install a new dishwasher in our home because it was not immediately next to the kitchen sink but about three feet away from it. Rather than pay a fortune to a plumber, I decided to install it myself, but the new dishwasher needed a new water supply. The old one had its own cold water supply line, but the new one had to be hooked up to a hot water. This simple T-valve made it really easy for me to connect the dishwasher to the kitchen sink hot water, and saved me the cost of calling a plumber, which I really appreciate!
G**E
Great high quality valve.
These worked excellent. I would highly recommend them. No leaks. They look and feel of high quality.
R**R
I'm not impressed!
Bought these 3/8 compression to 1/4" to install a large water filter and make the transition to 1/4 Ice machine and single serve water faucet lines.... "THEY JUST LEAK" First off compression fittings should not be that hard to seal. I've even used Teflon tape and tightened the HELL out of them to the point of fearful of twisting off. STILL leak!!! [a small drip,.. but can't have that anywhere, especially under a sink!]Probably will be returning...
J**A
Excelente relación precio
Bien
K**K
👍
👍
K**.
Perfect for my needs
I recently replaced my bathroom vanity and faucet. I bought the longest water lines I could find and they were just a hair to short to connect to the valve without stretching and bending. I could not find a 90° fitting that would work to save my life. I bought this and put a stop valve cap with thread tape on one end to get the 90° elbow I needed. This provided enough rise to give me a little slack on the lines. It wasn't my original plan, but it works.
P**T
Worked well, didn’t leak
Used it as a T at the supply line to attach a bidet for a Brondell bidet on a Koehler Persuade skirted toilet. Worked as expected with no leaks.
L**S
Tal y cómo se describe
Me gusto
D**.
Good product
Good product for the value
J**C
Great fit for most bidet
Simple and efficient
S**)
Solved my problem. Good value.
Used it to install a bidet. The bidet T is sized to be installed on the tank inlet which is hard to reach plus that T was metal and without a wing nut.Making the connection at the floor valve instead is readily accessible and less chance of leak. This product also came with Teflon tape and was priced right.It is worth mentioning the 3/8” NPT thread in North America is equivalent to the bidet hose of nominal 9/16”!!
ترست بايلوت
منذ 3 أسابيع
منذ 3 أسابيع