Question 1

I have the Pyle turntable and Pyle stereo but they don't work together--VERY low sound--so is this the missing piece?

Accepted Answer

Turntables (with typical magnetic cartridges) have very low signal output (a few thousandths of a volt). Records have the bass reduced to provide enough room on the surface for the recorded grooves, and the treble boosted to reduce the surface noise level when played back. Most modern receivers DO NOT have the right inputs to deal with this signal (no "phono" input). A phono preamplifier performs two jobs: - It boosts the small signal from the turntable by about 50 to 100 times (producing a "line level" signal) so it can be used by typical receivers or amplifiers.- It also boosts the bass and reduces the treble according to an industry standard (the RIAA equalization curve) to restore the signal from the record to its original frequency response.The Pyle PP999 is just an inexpensive phono preamp, nothing special. Phono preamps can range from $20 on up to whatever you're willing to pay for ultra-high quality. Some manufacturers make "USB" phono preamps that have A/D (analog-to-digital) converters built in and connect to a computer's USB port. Most of these provide "CD quality" conversion (16-bits at 44kHz or 48kHz). These may be adequate for digitizing your vinyl, but many computer sound systems can provide up to 24-bit, 192 kHz conversion depending on the software you use (much higher quality), by connecting the preamp output to the computer's line input. Don't just convert directly to MP3 files...you'll lose too much detail compared to the original vinyl sound. It takes almost no time to make an MP3 copy of a WAV or FLAC (lossless) file, but it'll take you an hour to make ANY digital copy of an LP, so do it the best you can the first time!

Question 2

So this is a stupid question, I plug my RCA wires coming from my turntable into the Amp. But where do I plug the speaker wires into on the Amp?

Accepted Answer

TurnTable==>PreAmp==>Receiver/Amplifier==>SpeakersThe 'Pyle PP999' is the "Preamp". The Turntable is plugged into the PP999 INPUT and the PP999 OUTPUT plugs directly into any (non Phono) INPUT on the receiver. Your Receiver allows you to switch between different music-sources, contains the primary-amplifier and distributes the final sound out to the speakers(and subwoofer). The Receiver should have multiple inputs for receiving signals from eg. CD, Tape, VCR, etc. In my experience those labels are for convenience and interchangeable with the exception of a "Phono" input. NOTE: If the receiver has a "Phono" input then there's a built-in preamp. If your using an external preamp (Pyle PP999) do NOT plug it into the Receiver's 'Phono' input, it could cause damage. I plug the preamp for the turntable into the Receiver's 'VCR' or 'TV' inputs.

Question 3

If I have a record player without a Preamp, will this help me with hooking it up to a Sonos?

Accepted Answer

You can hook it up to anything with a red and white connection. Or if you get the rca to 3.5mm jack then you can hook it up to anything with an input slot. I used this on my realistic lab 440 which doesn't have a preamp. Once I connected the ground from my turntable into the ground slot on this amp, my music sounded loud and clear.

Question 4

mp3

Accepted Answer

Turntables (with typical magnetic cartridges) have very low signal output (a few thousandths of a volt). Records have the bass reduced to provide enough room on the surface for the recorded grooves, and the treble boosted to reduce the surface noise level when played back. A phono preamplifier performs two jobs: - It boosts the small signal from the turntable by about 50 to 100 times (producing a "line level" signal) so it can be used by typical receivers or amplifiers.- It also boosts the bass and reduces the treble according to an industry standard (the RIAA equalization curve) to restore the signal from the record to its original frequency response.The Pyle PP999 is just an inexpensive phono preamp, nothing special. Phono preamps can range from $20 on up to whatever you're willing to pay for ultra-high quality. Some manufacturers make "USB" phono preamps that have A/D (analog-to-digital) converters built in and connect to a computer's USB port. Most of these provide "CD quality" conversion (16-bits at 44kHz or 48kHz). These may be adequate for digitizing your vinyl, but many computer sound systems can provide up to 24-bit, 192 kHz conversion depending on the software you use (much higher quality), by connecting the preamp output to the computer's line input. Don't just convert directly to MP3 files...you'll lose too much detail compared to the original vinyl sound. It takes almost no time to make an MP3 copy of a high bit-rate WAV or FLAC (lossless) file, but it'll take you an hour to make ANY digital copy of an LP, so do it the best you can the first time!

Best Sellers Rank	#3,348 in Electronics ( See Top 100 in Electronics ) #1 in Audio Component Preamplifiers
Customer Reviews	4.3 out of 5 stars 6,476 Reviews

Pyle Phono Turntable Preamp - Mini Electronic Audio Stereo Phonograph Preamplifier with RCA Input, RCA Output & Low Noise Operation Powered by 12 Volt DC Adapter - PP999

Description

Specifications

Common Questions