Bones Bearings Press Puller Bearing Tool Skate Tool

I live by the beach in Miami and use my longboard to get around almost everywhere, including to and from work as far as 6 miles each way. with all the puddles, sand and surprise florida downpours, i end up cleaning both mine and my girlfriends bearings quite often. I personally don't like using my trucks axles to pry out the bearings so I wanted something that I could use regularly to do this without damaging the bearings. This tool is amazing, its the size of a large keychain trinket, just a few inches long but made sturdy of all metal. The two balls on the end retract when you push the button at the top, allowing you to push it through the bearing, release the button and easily pull the bearing out, if you have spacers like me, you can use this tool just like your truck axels, insert it into the bearing, and use it as a lever to pry the bearing out. it fits so well into the center of the bearing that this causes no damage whatsoever. and it works just as well to push them back in.

Works great. Excellent way to remove bearings safely and easily. This is a great tool!! Small and stores easily. Just replaced an entire set of wheels with all new bearings and was a snap. I removed the bearings from the old wheels very easily and no damage tot he bearings.

They work with ease. Great tool if you change out wheels or clean your bearings often!

Best $15 I have spent so far in my short derby career. It took me 10 minutes to switch out my bearings, and most of that was cleaning the gunk off of them. It was a pleasure to pull and press them in, and I didn't feel like I was damaging my wheels like I did when I used a screwdriver to remove them. It is super small and easy to carry. I would like to sing love songs about this bearing press/puller.

It's better than trying to use an axel to pull bearings, but if you've got hard wheels (vanathane, fomacs, etc.), this little tool just doesn't give you enough leverage to really get the bearing out. You can work it for a while and slowly get the bearing to pull, bit by bit, but a hard wheel really needs the leverage of a bonafide bearing press. Either way, it's a nice tiny little tool to keep in a skate bag, and it's proved useful in helping others swap wheels out, specifically when they're using softer wheels.

If you break this product, you must be REALLY pulling/pushing on it. This is a great product and it's really easy to use. Before I bought this I used a screwdriver and my thumbs to put in and push out my bearings. But with this, I can do it really easy. I don't even need to touch the bearings. This is great if you take out an put in bearings a lot. It doesn't damage them at all.

This product works well... If your bearings aren't in too tight (doesn't work well for bearings jammed up in smaller diameter skate wheels) HOWEVER the tool is unnecessary because you can just use the truck axel to pop the bearing out of each wheel. However, do note that it cannot work on bearings which are longer (which include the bearing spacer effectively) such as Biltin Bearings because there is no space or gap behind which the balls can grip. I only wish it was not as expensive...

I used this to clean out my wheels of my outdoor skates. Turns out I have sealed ball bearings, but I still needed to remove them to clean my wheels. This bearing press puller is easy to use and made well. I recommend this product.

Nice

Good quality tool

Produit beaucoup trop cheap pour le prix demandé. Gros défaut de conception: la tige d'extraction est attachée au support en plastique. Le plastique est trop fin et casse. Si vos bearings rentrent facilement dans vos roues, cet extracteur fonctionne, mais dans ce cas pas besoin d'un extracteur, les trucks ou un tournevis suffisent. Si vos bearings sont durs a sortir, l'extracteur est trop cheap pour aider et va briser. Conclusion: ne pas acheter, beaucoup trop cher pour un produit aussi mal conçu, le rendant inutile et de mauvaise qualité.

Very nice

Product build quality is good but too costly and not does his work, it doesn't pull bearing and need to struggle a lot , we can pull bearing from nail easily but not from this tool.