Nilight LED Light Bar 2PCS 60W 4 Inch Flood Spot Combo LED Work Light Pods Triple Row Work Driving Lamp with 12 ft Wiring Harness kit - 2 Leads

I bought these lights to install onto my Bad Boy Magnum MX zero-turn mower. The included wiring harness with switch and relay was a big plus and reduced installation time. I ended up not using the included switch, as it didn’t fit the hole I wanted to use. To mount the lights, I went on Etsy and bought heavy duty front wheel spindle mount adapters. They basically clamp onto the spindle housing and then provide a 3/8 hole for the mounting stud on these lights. There were no mounting instructions, but it was pretty easy to figure out.On the wiring harness, pay attention to the spade connectors. Some of them were not crimped tightly requiring me to crimp them down some more.Installation was completed and the lights are bright and crisp. I was able to cut some grass during darkness as the led lights guide the way forward.Would recommend, it seemed like a good value compared to “factory” brand led light kits costing over $120.

I got these to put on my 2016 John Deere X590 tractor, mostly for blowing snow in the winter. They were pretty simple to install, and the long wire harness and switch are more than long enough for the tractor. I did add a couple of disconnects so I can change or dismount things easily later. They, and the the mounts that clamp to the top bar of the brush guard are also Nilight products. As usual, I went over the top with solder type connectors and heat shrink tubing, but I'm sure I could have installed the Nilight kit by itself just fine.The light are very bright and great for my needs. They seem like a really good value at this price, too.

The Nilight LED Light Bar 2PCS 60W 4 Inch is an excellent choice for anyone in need of powerful, reliable, and compact off-road lighting. These lights provide impressive brightness, delivering a wide, clear beam that significantly improves visibility during night driving or off-roading.With 60W of total power across two light bars, they produce a strong and focused light output that cuts through darkness and harsh weather conditions. The 4-inch size is perfect for mounting on vehicles like trucks, ATVs, or boats, and the sleek design ensures a perfect fit without looking bulky.Durability is another highlight of this LED light bar. Built to withstand tough conditions, it is IP67-rated for water and dust resistance, making it perfect for outdoor adventures in all weather. The aluminum housing ensures efficient heat dissipation, allowing the lights to run cool and last longer without issues.Installation is straightforward with included mounting hardware, and the light bars are designed to be shock-resistant, adding to their reliability for off-road trips. Whether you're looking to improve your vehicle’s visibility or simply add a rugged, stylish touch, the Nilight LED Light Bar is a fantastic option.

I bought the 60 watt LED light cubes along with the wiring harness.The wiring harness- Pros: very good quality terminals, wire, and the plastic surrounding the wire is very thick and durable. The rocker switch included works wonderful, and snapped right into the hole in my dash I drilled.Cons: One of the light wires were way too short, by about 2 feet. The switch wire was about 12 inches too short. I installed them as ditch lights on a 2013 Chevy 1500, but I think they would be too short for even the average car/suv. I had to extend the harness with my own wire, luckily I had plenty.The lights themselves-Pros: Very wide angle, mounting wasn’t terribly difficult, seem very sturdy and durable, wiring hooked to the lights was enclosed in a thick, durable plastic.Cons: Do not have much depth, can not angle them upwards at all due to the way that they are designed. Some people might think they look “bulky” although I do not.Overall, it’s not a bad buy for how much they cost. I am very satisfied with my purchase, as I was not expecting them to shine to the next county over. If you want that, go spend 200 bucks on some KC lights. For 30 bucks all together, you can’t beat this deal.Personally, I think this would be perfect for mounting to tractors, lawnmowers, or even for work lights on the back of a service truck.

These lights are super bright and rugged. They work perfect and do not flicker or bounce around. With flood and beam they light up a huge area for being cube sized. I have them on my agro 8 wheeler and they hold up great, very durable and easy to install.

My wife wanted some extra lights on her SUV for the back country roads at night or during poor visibility, & these work great. They are super easy to install, & are very bright. We love how the sides also emit light unlike others who have restricted sides. We did buy a different rocker switch because we didn’t like the round switch this kit came with. We also noticed that every time she started her truck, the 15amp fuse would blow. Not sure if anyone else had that problem? But we did-Some tips?- I decided to waterproof the connections that connect to the spades because the suggested way, would’ve took on moisture & water. I posted a pic above of what I’m referring to.- If you are gonna run more than one set of lights? I would recommend installing a new fuse box, you can get one on here that allows 6 to 12 extra fuses. Run 14g wire from the fuse box to the battery, & place the box where it would be more convenient to install all the new wiring.- Last, I would run wire loom on all the new wiring for extra heat & weather protectionBut if you are just running one set? You shouldn’t have a problem running them directly to the battery. Hope you enjoy your lights as much as we do!

Simple install on my 24 Bronco. I did get mounts for them so they’re not just bolted directly to my truck. Wiring made it super easy to connect. Hooked it to my #3 accessory switch. Nice and bright. Live off country road and helps me spot deer before I plow into them. Would buy again