Orpaz OWB Holster for CZ P07 Holsters and CZ P09 Holster

Nice quality. Positive click retention. Looks cool. FITS CZ P09 WITH HIGH SUPPRESSOR SIGHTS! I will buy these holsters for all my pistols that Orpaz has available.

I just received the thumb release holster for my suppressor ready CZ P-07. I was not sure if it would fit the high suppressor sights, but was pleasantly surprised to discover that it does; although just barely. The foolproof way to draw would be to tilt the weapon forward, so there is no chance of snagging the front sight. I understand that sometimes there are minute differences between each unit but I see no reason you can't file a small groove at the top to eliminate chances of a snag.

I use this for an Airsoft gun (ASG CZ P09), and it fits perfectly in this holster without any rattle (even when sprinting)! An added bonus is that it works with a smaller tracer unit attached to the threads (intended for airsoft pistols). I don't think it'll work with the regular size Acetech tracer unit though.

The Good: I was impressed by the build quality when I opened the package. The polymer is thick and molded well. Retention is very positive. You absolutely will not draw the weapon without pressing the release mechanism and no one is going to take it from you.The Bad: Release, however, is not positive at all. The bottom of the holster is sharp and grabbed onto the Picatinny rails and prevented a smooth draw especially when trying to draw quickly. Rounding it off with a jeweler's file and finishing with sandpaper fixed that. This would only be a problem with a pistol with a full rail, like the P09 and not the Glock with their proprietary rail. More evidence that this was designed for a Glock follows.Apparently there is a ratched spacer you're supposed to get to attach the holster to the bottom placement where I need it for my arm length, which is why I got the low ride version. It didn't come with it, which was highly annoying. I epoxied two steel washers together onto the ratchet hole in the position I want it in because I will never move it anyway. Why did I do that? Because the screw sleeve popped out when I was tightening it even though I WAS NOT over tightening. So I pulled the sleeve out, epoxied it back in, realized I didn't trust their dubious assembly and just epoxied everything together - the holster to the frame. It's now probably the most solid holster in the world - Thanks to my labor. I'm actually glad the spacer wasn't included because without it I may not have discovered the screw sleeves were garbage until I needed it not to fall apart. You know, like when someone is fighting me for my gun.The gun rattles like crazy in the holster. A little rattle is fine but this was insanely loose even with the tension screws tightened. This is because I'm sure they're using the same holster body for the Glock and the CZ and the Glock is significantly thicker. I heated it up with a hair dryer and squeezed it together. Now it fits snug and still draws well. Again, problem solved by my labor.The Ugly: The fact that I should have spent $50 more and gotten Safariland to build me an ALS for my P09. This is a good holster now, but a Jerry rigged holster I had to fix. Get the new Hogue holster if you want a cheaper option if you don't want to fix it. I honestly suspect the Glock holster will not have the fitment issues because they holsters are probably designed with Glocks in mind and made into P09 holsters as an afterthought.

I bought this so I could open carry my CZ P09 while out hiking. The retention is strong yet can be deactivated by a good push on the thumb button. The button seems stiff enough that it wouldn't be likely to be fully depressed on a fall, for example, but it has a gross "plastic on plastic" feel when depressing it that makes it feel kind of cheap.It also doesn't really fit snugly in the holster. I guess this is designed for the P07 and the P09, but my P09 wobbles around quite a bit inside the holster. I've tried messing with the retention screws and whatnot, but I can't seem to tighten it up and is probably my largest gripe.

I bought this for my ASG CZ P09 GBB (airsoft) sidearm. While I wish the mag release was better covered, the handgun fits rather well, nice smooth draw action, and it immediately locks back into place when it's dropped back in the holster.I also purchased the belt loop in case I run without my chest rig.

Great holster I purchased for a CZ p10f and had to do a little mod to the locking lug. Took me less then 10 min and some 800 grit sand paper. not much sanding at all.gun fits perfectly with a high rise front site.

I was worried due to some other reviews saying the suppressor height sights wouldn't fit, but they fit. The front sight is on the verge of catching, but out pulls out just fine every time. I bought this for the occasional open carry and for range use. With 0 adjustments it locks in real well.It also looks like it will work with a compensator, but not with anything attached to the rail like a laser or light.