OD 88mm/3.46"12mm Hex Wheel Rims Rubber Tires with Sponge Replacement for 1/10 RC Off-Road Buggy Car,Black

These are very nice quality wheels and tires. After using thin rubber CA to glue the tires to the rims (you absolutely HAVE to do this), I fitted these to my Rlaarlo X12S truck - these wheels are slightly bigger than the stock ones but the truck looks good with them fitted (see picture). It's not a fault of these wheels but I found I needed to use a 4mm plain washer to get the wheels to bolt tightly to this truck.I tried it on the paved street in front of my house and found that these were way better than the stock wheels/tires. Once these were fitted, this truck had much better traction on the road and on dirt, the slightly greater diameter tires also helped on grass.These are great looking and performing wheels/tires and, for the price, they are a bargain. Recommended.

Update: I've been tuning the RC I use these with and can say they hold up at 50 mph on 3S 120C with no ballooning. These are for sure the best all around tires for 92xx RCs.These need to be glued, like don't even think about trying to use them without glue. The glue helps strengthen the sidewall as well for added stability. Once they're glued? Oh baby.They're great for Amazon RCs. I put these on my modded 9206e 3S that hits 45 mph on the street. No ballooning at all. They held up to drifting and burnouts on asphalt with pebbles. They also take to white paint pens well for tire lettering.I've been using (more like abusing) these tires for about a month on rough concrete with no regard. Everyday for 2 hours in the Texas summer heat! Literally it's 98F but feels like 113F. They grip fantastic. I've eaten through 50% of the treads up front but so far they're still going strong!! Lightweight and well balanced. They look pretty good as well. I can't find anything negative to say.. and bought a few more sets.

The tires are worth it for the price.. They are smaller than normal 1/10th scale tires. You do need to glue them. Great grip!! They are perfect for beating around in grass amd gravel. Id buy again for another pair of all around beater tires, keeps me from smoking my good wheels and tires. FYI DO NOT PUT ON 4X4..

Horrible for high speeds

Purchased these to replace my oversized tires on a Redcat Racing truck and they fit well and performed well. The bead will need to be sealed as it broke during hard turning. They look great and the tires have a gripping thread pattern.

These wheels fit perfectly on the Rlarrlo Omni Terminator if you’re wanting to go after a more realistic scale look! After using Loctite liquid superglue to mount the tires to the rims properly, I have put these wheels to test using an upgraded 23T pinion on the stock motor and came across zero issues. Even at full speed, the tires did not balloon and the ride was stable on tarmac. I wouldn’t recommend these wheels for bashing around, but I think they would be fine!

I did a lot of looking and reading when it came to tires/wheels. Tons of reviews that seem like people just didn't read and do measurements. Are these perfect for a 1/10 scale vehicle depends on the vehicle for sure. I used them on my 1/16th Traxxas Mini Revo with a Mini Slash Body. The body needed some trimming but was expected. The tires and wheels were a bit larger than the OEM but only by a little. Fronts are narrower than the rears, so will probably be ordering another set to use the rears on the front and take the 4 front and use a buggy.The compound of the tire is medium-soft with a great tread pattern for sand/clay mix conditions. tires and wheels held up great on 2 days of track driving. Jumping 3-4' high and sending it out 10-12' long. I don't recommend bashing through rocks with the wheels but definitely a great option for the price.

The media could not be loaded. Actually they're not bad I just was expecting them to be a little more suitable for 1/10 scale but I'm not complaining cuz they're going to fit my Teton just fine with it with axle spacers