Wiper Blade Refill, Beigaon 28 inch Silicone Wiper Blade Refill for Replacement Windshield Wipers, (Strip Height: 11mm, Width: 6mm) Fit for Frameless Wiper Insert, DIY Cut to Size(Pack of 2)

[10/28] I tried to use the excess from the 17" blade and replace the rear insert. The 17" is the one I pulled the second channel off, and without that, it did not work. However, using the short piece I cut off for the 26" blade, it seems like it would still be very tricky, and may not work. The CRV rear wiper has the second channel similar to what these inserts have, but the CRV second channel is a little shorter than these silicone ones. If you spent a lot of time on it, you might be able to get it to work, but if the silicone is too jammed in there, it might not flex like you need it to. (I jammed the single channel scrap in with only one metal rod, and it would not flex enough, only the center was touching the glass)I found out a few helpful things. The blades are not 26", 17" and 12", they all measure shorter. I found the model numbers, and the millimeters are listed, and when converted to inches, it confirms what I measured. If you have a 2019 CRV the part numbers for just the inserts are:76622-TDK-J02 - 650mm Front Drivers = 25.6”76632-TZ3-A03 - 425mm - Front Passenger = 16.7”76722-TRN-H01 - 300mm - Rear = 11.8”They are about $5 each online.[10/24/2022] I have a 2019 Honda CRV. it came with nice blade-style windshield wipers in the front. This means replacing the "insert" (rubber/silicone) is perfect since the frame is good. Everyone online says silicone lasts longer than rubber, and most of the amazon listings that say silicone in the title, the reviews say they are rubber. So that's how I arrived at buying these. I measured the old rubber, and they are 6mm wide (wiper inserts are usually 6, 8 and 10 mm).However, I did not measure the height. The OEM inserts have one channel to slide into the frame these silicone ones have 2 channels. You can snip the end, and the one channel will tear off cleanly. But I would not recommend it. This is where the catch is. I snipped the second channel off, and the insert is now exactly the height of the OEM one. BUT the remaining channel is not 6mm. I did not measure it, but it is slightly fatter, just enough to not go in smooth. The problem is that sliding it into the channel is a giant pain in the butt. I ended up getting it in about 4 inches, and then pulling on it so hard the end popped out of the channel, that ended up helping though, I could get a better grip on it and pulled it really hard (it was stretching 3-4" but it's silicone, it appears fine - I can say 5 stars for sturdiness since it didn’t break). I then overpulled the silicone insert (because I needed to get the end back in that I had popped out). I then pulled the insert back to the right length while guiding it into the channel. Then I cut the excess off, and stuffed the last inch into the frame. I did this on my 17" blade. My 26” frame would have been a nightmare.Next, for my 26" blade, I left the silicone insert alone, and it took about 30 seconds and I was done. So now my 26" wiper sits taller than the OEM did, the 17" sits at the same height as the OEM. The next day we got a light mist, I tried these out, there was almost no noise (barely any water, plus freshly cleaned is the perfect recipe for a squeak). Both worked fine, so the extra height probably does not matter. In a harder rain, it might make a difference, or the wear and tear might be different. So, I will update this review if I notice anything different about the two different wipers.

Fits the front blades for my 2023 Chevy Bolt EUV. Wiper blades are kind of hard to find for this car since it uses a weird connector. It was pretty easy to remove the old rubber, cut the new silicone rubber to match the length, and insert the new silicone rubber into the blade. It seems to work well, and this was a fraction of the price of a new blade from the dealer (and even those are apparently hard to find).I saw another review saying they also replaced the rear blade's insert with this. I didn't try that because I'm not confident it would stay firmly in place with how the rear blade is designed. There's enough length, but I think the insert would slide out because it doesn't have a locking mechanism built into it. The front blades work because the front blades themselves securely hold the insert in place. Anyway, I'm more concerned about the front blades than the rear, so I'm happy with the result. I tested briefly in the garage with washer fluid. I haven't road tested it with actual rain yet, but I don't expect any issues. I would buy this again.

My rear blade rubber flopped and I needed a new one. I found reviews that recommended silicone over rubber for greater wiper quality. I bought this, cut it to size, and followed instructions in my owner’s manual. The thickness of the silicone tree is greater than the original old rubber. So, I had to use a tweezer tool to wedge inward until tucked and set underneath the grooves. It rained the next day and I tested the rear blade insert. It worked like a charm! Streak-free, smoothness, and high visibility. The curve is uniform. 4 stars for silicone insert being a tad bit overweight.

Great way to refill our Bolt EUV wiper blades. I’m not sure you can by replacement blades so it may be the ONLY way to refill.

Needed to replace the wiper blades on the new to me 2023 Bolt EUV. Saw a recommendation for these and went for it. Really easy change, these two blades are cut to size and you can make all 3 blades for the Bolt EUV. We will see how long they last, but at a fraction of the price of replacement blades, I think I will be way ahead regardless. Plus this causes less waste, which is nice.

Ordered these for a 2022 Tiffin Wyaferer. The blades came apart easily. Once I removed the wiper end caps(you tube how is my recommendation), I cut the new refills to match the length of the old rubber wipers with a single edge razor blade. They were easy to slide into the wiper arms. With the caps replaced I tested these silicone blades with a water hose. They worked great so far. The long blade on the driver side would chatter when the windshield was dry, but that didn't seem to be a real problem. Have not tried them in rain yet, but they seem great for a low price.

Extremely low quality. Leaves a trail of black residue. I tried cleaning it with a paper towel and glass cleaner, but even after repeated cleanings, the black carbon residue did not stop.

Works well with my 2020 Dodge Charge factory wiper blade. Just simply removed the rubber part and slide the new part in and Boom like new, i have it for about 1.5 years and they are still good. Wipe perfectly.