Signature Design by Ashley Honnally Modern Medallion Pattern Accent Chair, Blue & Ivory

Love this chair

I love this chair! I didn’t really care for the curvature of the back legs…at first….but now, I see that it adds to the uniqueness of the design. I wanted a different view when I entered the kitchen from the garage. The area is actually a breakfast area/laundry room combination. As you can see from the first photo, the view was not welcoming and definitely lacked the ‘wow’ factor. So I moved some things around and purchased this chair to ‘seal the deal’.It does require assembly and the instructions say two people are needed. I suppose you will need two people if you don’t have 30 minutes to invest, which is how long it took me (ALONE) from the time I dropped that first screw, until I placed the finished product in its final resting place. It was hilarious! I’d pulled out my tool bag and laid everything out on the living room floor: hammer, Phillips screwdriver, wood nails, etc. DIDN’T NEED ANY OF THAT!! Allen wrench and screws were already provided and that was ALL that I needed.****VERY IMPORTANT!*****The screws are grouped together by a rubber band. If you pull those out carefully as grouped, all you need to do is drop each set (bolt, nut, washer) in the specified slot. So happy with it that I really want to purchase another with a different pattern for another room in my home! It took me longer to write this review than to complete the assembly.😂

This chair arrived on time and was easy to assemble. The problem (for me) is that the seat height is only 13". My dining chairs are 17" and desk chair is 20". I simply could not get up out of this chair. I am a tall senior so knees did not like it. But nothing otherwise wrong with this chair. You might consider it for a youth.

Love this chair. Light comfortable easy to clean under and move around. It took about 10 minutes to assemble

The chair arrived yesterday and looks nice enough when assembled--just as in the picture on the website. Have no experience as to wear or sturdiness, so I'm basing the review on initial observations.The problem is that the assembly process turned out to be difficult. Theoretically this involved putting in 12 bolts though pre-drilled holes (2 for each leg) and four more to connect the back to the seat, using a provided Alan wrench. In practice it was difficult. Aligning the holes in the legs and back with the metal sleeves where you could screw in the bolts was a little tricky, but manageable. But then screwing down the bolts was time-consuming and tedious, because most of the holes were close to a barrier, so you kept having to remove and re-set the Alan wrench every half turn or so, and there were about 20 turns per bolt. A ratchet wrench was really needed and it would have saved a lot of time if they had included one of those.But that was only the beginning. The instructions say that you shouldn't screw down the bolts for the legs completely until the chair is assembled and you can set it on the floor and adjust the height of the legs so that the chair its level on the ground. This makes sense, except for two things: First, the legs have virtually no play since the bolts holding them are going through a hole, so it's impossible to move them up or down more than 1/8", if that. But, second, and worse, you can't screw down the back legs at all after the chair is assembled because they are part of the back assembly, and once you screw the back to the seat, you can't reach the bolts to tighten them. So you pretty much have to batten down the back legs before you assemble the chair, which is what I did.When I got done and put the chair on the ground, it looked like the front left leg was about half an inch short. I tried adjusting it as much as I could, but there was very little play. Do as I will, either the left front leg was too short or the front right leg was too long.I worked on it for a couple of hours and what I finally had to do is to take off the front right leg and drill out the holes to make them into a slot, so that leg could move up and down. This worked, and it had the added benefit that the chair seat now rested on the shoulder provided by the leg, whereas previously there was a gap. However, the left leg still has a gap. It's hard to explain this, so I'm including pictures. The one without the gap is the one I adjusted. Prior to my adjustment, it had a gap even bigger than you see on the other one.This is not an expensive chair so I can't complain too much about the fact that everything isn't flush. But they really could improve the product if they actually allowed some play in the legs so they could be adjusted up or down for levelling--of if they cut them more precisely so this wouldn't be necessary. A ratchet wrench--even a very cheap one--would also be very helpful.

I Love them

I didn't like that this chair color was so much more vibrant than photo I ordered it from, but that's what I get from couch shopping.I found assembly pretty much straight forward EXCEPT for the way the directions told you to insert legs, well, I had to figure out which direction they were to actually go. Pictures were not clear.The highth of the chair is as expected. It's a short sitting chair so buyers beware. Alot of reviews said they were expecting it to be taller.It is very sturdy, however I did tell my 9 yo that he is not to jump on it!! It's still a put it together furniture piece.