Panel Dolly, 600 Lbs Capacity, Drywall Mover with 8" Non-Flat Wheels, 0~10 Inch Adjustable Clamp Panel Cart, Wood and Fence Mover, Door Dolly KF4002

I'm a fire door chippy for 35 years so I know my stuff , this is by far the best door dolly I ve come across ticks all the right boxes clever and sturdy design my first impression is it'll outlast my working career, and still be doing it job well into my sons time on the tools .

As described A++

Saves my back when moving sheet material around. The only downside is the thumb turns aren't big enough to tighten properly. I've changed two for bolts and two for lever handles. This one was £10 cheaper because the box had been opened and resealed, bargain.

Good product. Can fit 3 fence panels onto it. Easy to manoeuvre, saves your back

Easy to assemble, brilliant for shifting heavy panels and sheets. I bought 2 of these in July 2022, both of them have wheel problems in march 2023. The spindles of the wheels tend to pull through the rubber wheels. The actual design is brilliant apart from the wheels. Thought I would leave a review whilst looking for new wheels.

I was surprised how sturdy this thing is. It’s strong enough to hold onto multiple OSB boards without tipping over and made it dead easy to move them. The solid tyres are a bonus too as it’s always ready to go.

Arrived in time. Panel dolly was not practical for internal move. Sadly I have to return.

Axles through the wheels are not strong enough for heavy loads but fine for a few sheets of ply or plasterboard.

会社で資材運搬用として購入しました。 1枚あたり約25kgある大きな板を運ぶ作業が多いのですが、このKASTFORCE KF4002を使うようになってから、一人でも安定して運べるようになりました。 耐荷重250kgの仕様は伊達ではなく、かなりしっかりした作りです。 フレーム剛性が高く、荷物を載せてもたわみや不安定さを感じません。 キャスターの動きも非常にスムーズで、方向転換時もストレスがなく、狭い通路でも扱いやすいです。 タイヤの回転も滑らかで、重量物を載せても軽い力で押し出せます。 パネル部分のサイズ感もちょうどよく、板やドア材の運搬に最適。 使用後は立てて収納できるので、作業場でも邪魔になりません。 以前は2人がかりで運んでいた荷物が、今では1人で安全に動かせるようになり、作業効率がかなり向上しました。 現場作業用や倉庫での使用にも安心しておすすめできます。

j'ai 75 ans ,je dois me ménager, présentement j'ai défait un garage pour le localiser ailleur sur mon terrain ,j'ai défait les murs en section de 8 a 12 pieds, avec mon voisin, j'ai roulé le mur a soixante pieds sans efforts, et des feuilles de contre-plaqué 3/4, un seul bémol, les roues devrait etre pneumatique pour rouler mieux sur gravier(ce que je vais faire).

I needed a way to roll my 24' extension ladder around as it almost too heavy for one person to move. This panel dolly was perfect for the job! It came in a sturdy cardboard box, shrink wrapped to hold all the pieces together in a nice easy to handle bundle. There was no assembly instructions included but it was easy to put together. Included are two eight inch airless rubber wheels, four washers (two for each wheel, one washer is placed on the axle before the wheel is installed and the other washer is placed on the axle after the wheel is installed), my kit had three R-clip pins to fasten each wheel to its axle so I have a spare, there are two heavy duty 14" x 1" square chrome plated steel tubes, and 4 thumb nuts used to fasten the 8 1/2" tall heavy duty steel sliders to the tubes. The thumb nuts make it easy to adjust the width of the dolly to match your load. The box says the panel dolly can accommodate loads upto 9" wide but I found I can actually go almot to ten inches. The box says the clamping plates are 15"x16" but mine are actually 8 1/2" tall by 16" wide. For moving doors and paneling, I like the 8 1/2" tall height. With loads, the panel dolly rolls very nicely. This tool will make a nice addition to my tools. If your looking for a well built, heavy duty panel dolly, you should try this one out. I am sure you'll like it as much as do.

Pesa y hay que ajustar el ancho bien. pero cumple su función

I had to drill out the box beams so the thumb turns would lock the mouth in place. I use it for moving steel doors during large commercial warehouses construction. Rolls over extension cords on slab no problems. A bit pricey… but solid and fuctional.