AKIHISA 2 Pack Ceiling Mount Pipe Support 304 Stainless Steel pipe support bracket For wall mount pipe support ID Range 1 7/9 Inch(45-48mm)(50+50mm)

Received quickly, good quality, exactly as described/shown. Would purchase again if needed.

I needed to mount a couple PTZ security cameras to round posts. The cameras only came with brackets for flat surfaces. So I used the split ring end of this hanger on the post side and I used a ~3" x ~5" x 3/4" thick high density plastic block in combination with thread rolling screws to attach the three hole circular plate end. On the other side of the block, I attached the camera bracket with the same thread rolling screws. The result is the cleanest looking and most effective camera mounting system I've seen at a decent overall price anywhere. Although, you have to be a little bit mechanically inclined and have a power drill to go this route. You have to drill very small holes in order to get your rolling screw into the plastic block. I would not recommend using any other type of screw. You could also drill through and use nuts, bolts, and washers instead of screws. For the screws, I used a slightly smaller diameter hole than specified for my rolling screw size but it still worked great. I have cameras mounted as high as 17 ft in the air on round pipe posts using this method. It looks very professional as well. It only takes a few minutes to fabricate if you have the right tools.

Ordered the 3 inch clamps for 3 inch pvc and the provided bolts are not long enough

Works good, but sizing may be slightly off. Lock nut on the threading into the base helps a lot with stability. It's not the prettiest job, but after replacing my water heater and using flexible connections, the pipes were no longer secure, so these took care of that. One thing to note is that in the pictures you are looking at 3/4" copper pipes and 0.74"(15-19mm) hangars. They would clearly work just fine for 1/2" pipes too, and in my opinion were probably designed for 1/2" pipes, since with a 3/4" pipe the lock nuts on the clamps themselves do not even thread all the way through. This is actually the smallest size available in the type I ordered (the longer type), so I don't think I received the wrong size by mistake. I did not have any missing parts unlike another reviewer, all six lock nuts were included.The end result isn't ideal, but I'm sure it'll hold until the plumbing needs to be replaced entirely. I did not use any of the screws or plugs provided, I pre-drilled my own holes and used more heavy duty torx wood screws. I personally don't trust the smaller hardware (like screws) that come with these kinds of things, and would suggest using your own if you can.

I used these to lock a brass gas manifold in place. Zero problems.

Using these beauties on my latest Krafty Artisan project...at beginning of a working lava lamp/ light fixture airplane with 3 running props...just have to see it...still in process.Amazing product to support lava lamp part with a few adjustments. Love the finish on these and they are sturdy. These will be bolted to a finished plaque...just imagine...into the air....only request for me would be ability to put a longer threaded rod on 1 of these. Not the use they were intended for...but they are great for a crafter or repurposed like me 😎👍..thanks much

The threaded rod doesn't have much bite and is rather sloppy. I had just assumed this was for 3" PVC, it didn't fit very well at all but will work fine for a Radon Vent.Consult a chart and order your size based off OD of pipe you're using, not ID.

I had no problem and the job was done perfectly. I recommend it to replace plastic support of my UV tube. They were melted and their "C" shape changed with the heat produced by the UV lamp inside the tube.

Parfait pour renforcer un robinet bain sur patte

It is hard to believe how good it is for such as price.

I bought this to hang/support 3/4 in copper pipe and the M8 nuts are not long enough to close the clamp around the copper pipe, and are therefore not long enough to make use of the locking nut on either side of the clamp.